Ballasts / Chokes

LUMii Digita 600W Electronic Ballast is an electronic/digital ballast with the ability to dim (reduce or increase power) 600W high-pressure sodium (HPS) or metal-halide (MH) lamps. LUMii Digita 600W Electronic Ballast is an electronic ballast with an integrated microprocessor that controls and operates at a higher frequency than standard analogue ballasts. Higher efficiency means more light for your plants. It enables rapid lamp ignition, saving energy. Quieter than any other ballast. Measurements show up to 30% more brightness than analogue ballasts. The electronic ballast solves irregular mains voltage issues. Analogue ballasts age, become noisy, consume more electricity and get hotter while light output drops. Electronic ballasts do not do this; they maintain the same output and efficiency. For safe operation, the LUMii ballast is programmed to switch off in the event of a short circuit, lamp failure or no lamp fitted.

​

• operating modes with a 600W lamp: 250W, 400W, 600W
• operating modes with a 400W lamp/bulb: 250W, 400W, do not "dim" above 400W!
• operating modes with a 250W lamp/bulb: 250W, do not "dim" above 250W
• Supply voltage: 220–240V 50Hz
• Current: 1.8A
• Input power: 620W
• Output power: 600W
• Power factor: >0.99 THD
• Non-linear distortion: <10%, Imax:Iavg. <1,7
• Ambient temperature: from -25°C to 70°C
• Heating (Δt): 29°C
• Protection class: >IP23
• ​Dimensions L/W/H: 43/38/18.5 cm
• Weight: 3.125 kg

Disconnect the power when changing the lamp!

LUMii BLACK 600W Electronic Ballast is an electronic/digital ballast with "dimming" capability (reducing or increasing power) for 600W high-pressure sodium (HPS) or metal-halide (MH) lamps/bulbs.

• 4 operating modes: 250W, 400W, 600W, 600W boost (+10%)
• aluminium housing suitable for wall mounting.
• cable with Schuko plug for connection to the mains
• IEC connector (computer type) for connecting the lamp
• Voltage: 240V
• Current: 2.9A
• Power cable: 2m
• Dimensions L/W/H: 29/12/6cm
• Weight: 3kg
• Warranty: 1 year

The electrical fuse is located beneath the power socket — please check the fuse if the ballast is not working!

• operating modes with a 600W lamp/bulb: 250W, 400W, 600W, 600W boost (+10%)!
• operating modes with a 400W lamp/bulb: 250W, 400W, do not "dim" above 400W!
• operating modes with a 250W lamp/bulb: 250W, do not "dim" above 250W

Disconnect the power when changing the lamp!

Maxibright Warpdrive 600W Power Pack is a budget electronic ballast designed to operate high-pressure sodium (HPS) or metal-halide (MH) lamps / bulbs rated at 600W. It has no "dimming" capability (reducing or increasing power)!

• operates silently
• extremely lightweight and compact
• works with HPS and MH bulbs

Note: the product is supplied with UK plug* (UK-standard plug) and IEC-14 female connector*!

Features:

• power: 600W
• dimming capability: none
• ​voltage: 240V
• frequency: 50/60Hz
• Imax: 3.5A
• weight: 1.135kg
• dimensions: 241/100/60mm
• warranty: 1 year

Note: the product is supplied with UK plug* (UK-standard plug) and IEC-14 female connector*!

HortiLight Ballast 600W is an excellent addition to any grow room for those seeking a high-quality and reliable magnetic ballast at a reasonable price. It is designed to operate HPS (sodium) and MH (metal-halide) lamps.

• for HPS and MH lamps
• power: 600W
• power consumption: 3A
• voltage: 220/240V, 50Hz
• dimensions L/W/H: 310x144x120mm.
• weight: 6.4kg.

Mari 600W is a high-quality and durable product – one of the best and best-selling in its class on the market. The lighting kit is designed to work with HPS (sodium) and MH (metal-halide) lamps.

• the kit includes: magnetic ballast, igniter and capacitor
• for HPS and MH lamps
• power: 600W
• power consumption: 6.2A
• voltage: 230V, 50Hz
• dimensions L/W/H: 295x110x115mm
• weight: 6.4kg

LUMATEK 600W 240V CONTROLLABLE BALLAST is a digital controllable ballast that can operate with both high-pressure sodium (HPS) and metal-halide (MH) lamps. It provides stable and precise voltage to the lamp, creating higher PAR/PPF output and is nevertheless far more energy efficient than most ballasts on the market! The ballast features intelligent start technology and a soft-dimming mechanism! It can be externally controlled with LUMATEK Control Panel Plus 2.0 (sold separately).

• Output power: 600W
• 4 operating modes: 250W - 400W - 600W - 660W
• generates very little heat compared with other ballasts on the market
• operates silently
• Protection against short circuit, overheating, overvoltage / undervoltage, end of lamp life!
• 5-year warranty!

An electronic ballast is a solution to the problem of irregular voltage in the power grid! Magnetic ballasts age over time, begin to make noise and consume more electricity, heat up more and more while their light output decreases. This does not happen with digital ballasts—they maintain the same level of output and efficiency. LUMATEK ballasts are programmed for “soft start”, meaning no voltage or current peak is required to start the lamp; this extends bulb life, does not overload the electrical installation and allows a larger number of ballasts to start safely at the same time.

Full technical specifications:

• Output power: 600W
• Input voltage: 240V, 50/60Hz
• Maximum current: 2.7A
• power factor*: > 0.99
• Efficiency: 96%
• THD*: < 8%
• Dimming capability / 4 operating modes: 250W - 400W - 600W - 660W
• Compatible with: 250W, 400W, 600W HPS / MH lamps
• Operating frequency: high frequency
• generates very little heat compared with other ballasts on the market
• operates silently
• Protection against short circuit, overheating, overvoltage / undervoltage, end of lamp life!
• Dimensions: 310 x 114 x 81mm
• Weight: 2.7kg
• warranty: 5 years

Operating instructions:

• For use with a 250W HPS or MH lamp: the ballast must be always and only in 250W mode!
• For use with a 400W HPS or MH lamp: the ballast must never be in 600W or 660W mode!
• For use with a 600W HPS or MH lamp: Start in 600W mode and only after the lamp has fully warmed up (after approximately 10min. of operation), can you switch to 660W mode!

1. Disconnect the power when changing the lamp!
2. LUMATEK recommends replacing the lamp after 6-12 months of operation!
3. VERY IMPORTANT: allow the lamp to cool completely (20-30min.) before switching it on again! (Doing otherwise shortens its life.)
4. Also, do not switch the lamp off before it has reached full power!

Electromagnetic hybrid ballast with soft start for 600W sodium (HPS) and metal-halide (MH) lamps/bulbs. It consists of a choke, starter ("ignitor"), capacitor and control circuit.

• power: 600W
• power consumption: 660W
• 230V, 50 Hz
• λ>0,9; starting voltage 3.2KV
• protection class IP 20
• dimensions L/W/H: 290x100x80mm
• weight: 6,4kg
• warranty: 1 year 

LUMii SOLAR 315W CMH FIXTURE lighting kit, which includes:

• Electronic ballast + reflector

LUMii Digita 1000W Electronic Ballast is an electronic/digital ballast with dimming capability (reducing or increasing power) for 1000W high-pressure sodium (HPS) or metal-halide (MH) lamps. LUMii Digita 1000W Electronic Ballast is an electronic ballast with a built-in microprocessor that controls and operates at a higher frequency than standard analogue ballasts. Higher efficiency means more light for your plants. It enables rapid lamp ignition, saving energy. Quieter than any other ballast. Measurements indicate up to 30% more brightness than analogue ballasts. The electronic ballast solves the problem of irregular mains voltage. Analogue ballasts age over time, become noisy, consume more electricity and heat up more while their light output decreases. This does not happen with electronic ballasts: they maintain the same emission level and efficiency. For safe operation, the LUMii ballast is programmed to switch off in case of a short circuit, lamp failure or a missing lamp.

​

• Operating modes with a 1000W lamp: 250W, 400W, 600W, 1000W
• Operating modes with a 600W lamp: 250W, 400W, 600W, do not dim above 600W!
• operating modes with a 400W lamp/bulb: 250W, 400W, do not "dim" above 400W!
• operating modes with a 250W lamp/bulb: 250W, do not "dim" above 250W
• Supply voltage: 220–240V 50Hz
• Current: 4.6A
• ​Dimensions L/W/H: 48/39.5/24.5 cm
• Weight: 5.2 kg
• Warranty: 1 year

Disconnect the power when changing the lamp!

LUMATEK 1000W 240V CONTROLLABLE BALLAST is a digitally controllable ballast that can operate with both sodium (HPS) and metal-halide (MH) lamps. It provides stable, precise voltage to the lamp, delivering higher PAR/PPF output while being far more energy-efficient than most ballasts on the market. The ballast features intelligent start technology and a soft-dimming mechanism. It can be externally controlled with the LUMATEK Control Panel Plus 2.0 (sold separately).

• output power: 1000W
• 4 operating modes: 600W - 750W - 1000W - 1000W SL
• generates very little heat compared with other ballasts on the market
• operates silently
• Protection against short circuits, overheating, overvoltage / undervoltage and end of lamp life!
• 5-year warranty!

An electronic ballast is a solution to the problem of irregular mains voltage. Magnetic ballasts age over time, become noisy and consume more electricity, while heating up ever more as their light output declines. This does not happen with digital ballasts: they maintain the same output and efficiency. LUMATEK ballasts are programmed for a “soft start”, meaning no voltage or current spike is required to start the lamp. This extends bulb life, does not strain the electrical installation and enables more ballasts to be started safely at the same time.

Full technical specifications:

• output power: 1000W
• Input voltage: 240V, 50/60Hz
• max. current: 4.7A
• power factor*: > 0.99
• THD*: < 10%
• dimming capability / 4 operating modes: 600W - 750W - 1000W - 1000W SL
• compatible with: 600W, 750W, 1000W HPS / MH lamps
• operating frequency: high frequency
• generates very little heat compared with other ballasts on the market
• operates silently
• Protection against short circuit, overheating, overvoltage / undervoltage, end of lamp life!
• dimensions: 318 x 166 x 96mm
• weight: 4.25 kg
• warranty: 5 years

Operating instructions:

• for use with a 600W HPS or MH lamp: the ballast must always be set to 600W mode only!
• for use with a 750W HPS or MH lamp: the ballast must never be set to 1000W or 1000W SL mode!
• for use with a 1000W HPS or MH lamp: start in 1000W mode and only after the lamp is fully warmed up (after around 10 min. of operation), you can switch to 1000W SL mode!

1. Disconnect the power when changing the lamp!
2. LUMATEK recommends replacing the lamp after 6-12 months of operation!
3. VERY IMPORTANT: allow the lamp to cool completely (20-30min.) before switching it on again! (Doing otherwise shortens its life.)
4. Also, do not switch the lamp off before it has reached full power!

Agrolite Magnetic Ballast CL2 CMH 315W is a lighting kit designed to work with the latest-generation CMH / CDM lamps (ceramic metal-halide / ceramic discharge metal-halide lamps).

• the kit includes: magnetic ballast, ignitor and capacitor
• mains cable: 1.5m.
• lamp cable with C13 connector: 0.2m
• for CMH / CDM lamps
• power: 315W
• power consumption: 3.64A
• voltage: 220/230V
• box dimensions L/W/H: 298x128x115mm.
• weight: 6.2kg.

• The professional choice in lighting fixtures.
• The set includes a Gavita Pro 1000W 400V DE EL lamp with an output of 2100 μmol s-1.
• Illuminates more than 2 sq.m with 2000 μmol s-1.
• The most efficient, highest-output model on the market (Energy efficiency class: A++)
• Compatible with the Gavita Master controller.
• Easy installation — plug in and use.

Gavita Pro 1000e DE

The best lighting is now even better

The new Gavita Pro e-series are improved models of Gavita's existing classic lighting fixture series, now compatible with and adapted for complete lighting control via a Gavita Master controller. You can now control the light with just a few simple button presses.

Gavita Pro HPS fixtures are the professional standard for efficient lighting. Operating at standard 240V, they power high-voltage (400V) electronic horticultural lamps, which outperform ordinary ones in spectrum, light output and lamp efficiency during extended use.

• Fully encapsulated wiring with a GORE-TEX ventilation outlet, no moving parts, completely silent and with almost imperceptible heat output.
• Compatible with high-frequency electronic (400V) horticultural lamps, which have 10-25% greater light output.
• Highly efficient — retain more than 95% of their light-reflecting properties, so you only need to replace the bulb once a year.
• Replaceable Gavita HR96 reflector with 96% reflectivity for maximum efficiency.
• Controlled output: With one knob, increase or decrease the amount of supplied light according to the conditions or development stages of your plants.
• A "soft" light-dimming system allows gradual reduction of emitted light, eliminating stress on the lamp when its supplied current changes.
• Equipped with high-frequency (>100kHz) Gavita electronics.
• No problems caused by electromagnetic interference.

Specifications here!

Electrostart 1000W is a lighting kit designed to operate with HPS (sodium) and MH (metal-halide) lamps.

• the kit includes: magnetic ballast, igniter and capacitor
• for HPS and MH lamps
• power: 1000W
• power consumption: 10.3A
• voltage: 230V, 50Hz
• dimensions L/W/H: 25 x 17 x 9 cm.
• weight: 12.0 kg.

If you have a damaged ballast on your Lumatek - ZEUS, we offer the possibility to purchase it as a spare part. 

Electronic Ballast for LED lighting fixtures Lumatek - ZEUS PRO 2.9 and 3.1 models 600W

• New! The right light for your room size.
• The set includes a Gavita Pro 750W 400V DE EL lamp with an output of 1500 μmol s-1.
• Illuminates more than 1.5 m² with 1000 μmol s-1.
• High-efficiency operating range from 600 to 825W.
• Compatible with the Gavita Master controller.
• Easy installation — plug in and use.

Gavita Pro 6/750e DE FLEX

The best lighting is now even better

The new Gavita Pro e-series are improved models of Gavita's existing classic lighting fixture series, now compatible with and adapted for complete lighting control via a Gavita Master controller. You can now control the light with just a few simple button presses.

New to the Pro line e-series is the 6/750e DE FLEX unit, which uses the recently developed Gavita Pro 750W DE 400V EL lamp. The lamp's operating range is 400-825W, placing it in the large gap between 600- and 1000-watt lamps. We named it 6/750 DE FLEX because it is equally efficient when operating at 600 watts and at 750 watts. In many cases, it is a suitable replacement for a 1000-watt ventilated unit operating at 825W, which can save you up to 20% electricity. The output of the lamp operating at 750W is 1500 μmol s-1 (2μmol s-1 per watt).

Gavita Pro HPS fixtures are the professional standard for efficient lighting. Operating at standard 240V, they power high-voltage (400V) electronic horticultural lamps, which outperform ordinary ones in spectrum, light output and lamp efficiency during extended use.

• Fully encapsulated wiring with a GORE-TEX ventilation outlet, no moving parts, completely silent and with almost imperceptible heat output.
• Compatible with high-frequency electronic (400V) horticultural lamps, which have 10-25% greater light output.
• Highly efficient — retain more than 95% of their light-reflecting properties, so you only need to replace the bulb once a year.
• Replaceable Gavita HR96 reflector with 96% reflectivity for maximum efficiency.
• Controlled output: With one knob, increase or decrease the amount of supplied light according to the conditions or development stages of your plants.
• A "soft" light-dimming system allows gradual reduction of emitted light, eliminating stress on the lamp when its supplied current changes.
• Equipped with high-frequency (>100kHz) Gavita electronics.
• No problems caused by electromagnetic interference.

Specifications here!

• For use with 600W EL lamps only
• No acoustic resonance
• Up to 8% more light from the lamp
• Efficiency after 5000 operating hours - >95%
• System design and concept by Gavita
• Sealed (Class I), with a ventilation outlet made of Gore Tex
• Microprocessor-controlled, with LED ballast-status indicator
• Professional UV-resistant wiring
• Extremely low heat output and optimal cooling

Gavita Pro 600 SE

Gavita Pro 600 is the first 240-volt electronic ballast to power professional 600W 400V EL (electronic) lamps. These lamps deliver the best PAR output, an improved spectrum and the best light-output retention (>95% PAR after one year of use). The lamp is the most efficient horticultural lamp on the market and the only one designed specifically for electronic ballasts.

Gavita Pro 600 is available as a complete kit including a professional HortiStar HR 96 reflector, or as a separate ballast ideally matched with a Gavita Triple Star reflector. The ballast is fully enclosed and has no cooling fan, as it emits very little heat during operation. This enables safe, easy installation close to your lamp, reducing the electromagnetic interference reaching the ballast and significantly extending its service life and efficiency. The kit is easily installed using two bolts.

Specifications here!

Electrostart 600W is a lighting kit designed to work with HPS (sodium) and MH (metal-halide) lamps.

• the kit includes: magnetic ballast, igniter and capacitor
• for HPS and MH lamps
• power: 600W
• current draw: 6.2A
• voltage: 230V, 50Hz
• dimensions L/W/H: 24 x 14 x 9cm.
• weight: 7.5kg.

• For use only with 1000W 400V DE EL lamps
• No acoustic resonance
• Up to 8% more light from the lamp
• Efficiency after 5000 operating hours - >95%
• System design and concept by Gavita
• Sealed (Class I), with a ventilation outlet made of Gore Tex
• Microprocessor-controlled, with LED ballast-status indicator
• Professional UV-resistant wiring
• Driver efficiency at full power - 95-96%
• Extremely low heat output and optimal cooling

Gavita Pro 1000 DE

Gavita Pro 1000 DE is the first 240-volt electronic ballast designed to power professional 1000W 400V DE EL (electronic) lamps. These lamps offer the best PAR output, an improved spectrum and the best maintenance of light efficiency (>95% PAR after one year of use). The lamp is the most efficient horticultural lamp on the market and the only one designed specifically for electronic ballasts.

Gavita Pro 1000 is available as a complete kit including a professional HortiStar HR 96 1000 DE reflector, or as a separate ballast. The ballast is fully enclosed and has no cooling fan, as it emits exceptionally little heat during operation. This allows safe, easy installation close to your lamp, reducing the amount of electromagnetic interference that reaches the ballast and significantly extending its service life and efficiency. The kit is easy to install using two bolts.

Specifications here!

Secret Jardin CARRYIT ballast holder.

• Dimensions: 14cm x 43.3cm x 3.5cm
• Weight: 368g

Recommended for:

• ballast with dimensions: 11cm x 35cm