Timers and controllers

Cornwall Electronics is a speed controller that reduces the speed of a compatible fan using a rotary knob.

Features and functions

• Power supply: 230 V, 50 Hz.
• Maximum power rating: 280 W.
• Maximum current rating: 1.6 A.

Check that the motor is compatible with this control method and observe both the current and power limits. Do not set a speed at which the motor cannot run steadily.

Choosing a climate controller

Match the load type to the control method. An AC fan with adjustable voltage and an EC fan with a signal input require different controls. Follow the limitations of the specific model.

View ventilation and climate controllers.

The PLANTiT Water Timer is designed to connect to a tap, but can also be used for gravity-fed irrigation from a barrel or tank. The timer is programmed in just 2 easy steps - turn the Run Time dial to set your desired watering duration, and the Frequency dial to set the desired interval between waterings. Then connect it to the irrigation outlet pipe and the timer will take care of the rest.

• Designed to connect to a tap
• The protective cover makes it fully waterproof
• Powered by two 1.5V AAA batteries (not included), which can last a whole season without needing replacement
• Automatic shut-off valve for when the battery runs out, and a program delay button for when you need to maintain your plants and don't want to water them
• Supplied with a set of fittings and a built-in filter

Technical specifications:

• Operating pressure range: 0-150 PSI (0-10 BAR)
• Connection: ¾ male / female connector / hose connector
• Frequency: choose to irrigate every 1, 2, 3, 4, 6, 8, 12, 24, 48 or 72 hours, or once a week
• Run time (watering): 1, 3, 5, 10, 15, 20, 30, 60, 90 or 120 minutes

Before setting the watering schedule

Take the inlet pressure, water source and watering duration into account. Check the flow rate with a test cycle.

Browse irrigation timers and ready-made irrigation systems.

Synchro TS-ED1 is a weekly digital timer that automatically switches an electrical appliance on and off via a power outlet.

Features and functions

• Up to 8 on/off programs based on the days of the week.
• ON, AUTO, and OFF modes.
• Select a 12- or 24-hour format and daylight saving time function.
• Power supply: 220–240 V. Rated limits: 16 A and 3500 W.

Set the current day and time, then set the on and off times and select AUTO. Check that it switches correctly with a test cycle.

Timer selection

Compare daily and weekly programs, minimum increments, and load capacity. The starting current of a pump, ballast, or LED driver may limit the number of connected devices.

Browse analog and digital timers.

Synchro TS-MD3 is a mechanical plug-in timer with a recurring 24-hour program.

Features and functions

• Minimum setting increment: 15 minutes.
• Daily cycle: 24 hours.
• Power supply: 220–240 V.
• Rated limits: 16 A and 3680 W.

Set the current time and dial segments according to the instructions. Mechanically setting the program does not mean the clock has a backup power supply in the event of a power outage.

Choosing a timer

Compare daily and weekly programs, minimum increments, and rated load. The startup current of a pump, ballast, or LED driver may limit the number of connected devices.

Browse analog and digital timers.

The CORNWALL humidity controller is the ideal device for maintaining optimal humidity for your crop. Connect it to your humidifier or dehumidifier and set the desired humidity. The controller will take care of the rest.

• Voltage: 230V AC/50HZ
• Maximum load: 16A 3680W
• Inductive load: 2A 460W 
• Operating temperature: 5°C - 40°C
• Storage temperature: -10°C - 50°C
• Controlled humidity range: 20% - 90%
• Accuracy: ±5%
• Reporting period: 10 sec

Before use, please read the instructions:

• Before setting the humidity, select the operating mode - dehumidification (fan icon) or humidification (droplets icon). In "dehumidification" mode, the controller supplies power when humidity exceeds the set value; in "humidification" mode, when humidity falls below the set value.
• To change the operating mode - press ON/OFF and the "up arrow" together for 3 seconds.
• Default setting: Humidity (SET): 40%; Mode: Humidification
• Setting the humidity - press ON/OFF

Humidification mode (icon: droplets):

• use the arrows to set the SET value at least 5% above the RH humidity (the currently measured humidity). After a few minutes, the indicator will light green and the controller will start supplying power;
• when the room humidity (RH) reaches the level set in SET, the indicator lights red, the droplets disappear from the screen, and the controller stops supplying power.
• when the room humidity (RH) is above the level set in SET, the indicator lights red and the controller will not supply power.

Dehumidification mode (icon: fan):

• use the arrows to set the SET value at least 5% below the RH humidity (the currently measured humidity). After a few minutes, the indicator will light green and the controller will start supplying power;
• when the room humidity (RH) drops to the level set in SET, the indicator lights red, the fan disappears from the screen, and the controller stops supplying power.
• when the room humidity (RH) is below the level set in SET, the indicator lights red and the controller will not supply power.

Important:

• Do not connect a power strip downstream of the controller!
• Do not connect devices that transmit vibrations to the controller!
• Ensure the safety of heating and moving devices!
• Protect from moisture, extreme temperatures, shocks, and vibrations!
• Use indoors only; do not expose to sunlight!
• Keep out of reach of children!

Charge the battery when the device displays "LO" - by plugging the device into an outlet!

Distinguish the maximum load of 16 A / 3680 W from the specified inductive load of 2 A / 460 W. For a motor, compressor, or other inductive device, observe the lower allowable limit.

Choosing a climate controller

Match the load type and control method. An AC fan with adjustable voltage and an EC fan with a signal input require different controls. Follow the limits for the specific model.

Browse ventilation and climate controllers.

Cornwall temperature controller, ideal for stabilizing the temperature of your crop. It can be used with an air conditioner or other heating appliances (heaters), depending on the selected function.

• Voltage: 230V AC/50HZ
• Maximum load: 16A 3680W
• Inductive load (exhaust fan): 2A 460W 
• Operating temperature: 0°C - 40°C
• Storage temperature: -10°C - 50°C
• Controlled temperature: 5°C - 30°C / 40°F - 85°F
• Accuracy: ±1°C / ±3°F
• Reading interval: 10 sec

Please read the instructions before use:

• Before setting the temperature, select the operating mode - cooling (snowflake icon) or heating (flame icon). In "cooling" mode, the unit supplies power when the temperature exceeds the set value; in "heating" mode, it supplies power when the temperature drops below the set value. To change the operating mode - press ON/OFF and "up arrow" together for 3 seconds.
• To switch between °C and °F - press the "up arrow" and "down arrow" together for 3 seconds
• Default setting - cooling; 20°C
• Setting the temperature - press ON/OFF

Cooling mode:

• Use the arrows to set the "SET" temperature at least 2° below the "RM" temperature (the current measured temperature). After a few minutes, the indicator will glow green and the controller will start supplying power.
• When the "RM" temperature reaches the "SET" temperature, the indicator will glow red and the snowflake icon will disappear from the screen; the controller will stop supplying power.
• When the "SET" temperature is above the "RM" temperature, the indicator will glow red and the controller will not supply power.

Heating mode:

• Use the arrows to set the "SET" temperature at least 2° above the "RM" temperature (the current measured temperature). After a few minutes, the indicator will glow green and the controller will start supplying power.
• When the "RM" temperature reaches the "SET" temperature, the indicator will glow red and the flame icon will disappear from the screen; the controller will stop supplying power.
• When the "SET" temperature is below the "RM" temperature, the indicator will glow red and the controller will not supply power.

Important:

• Do not connect a power strip after the controller!
• Do not connect devices that transmit vibrations to the controller!
• Ensure the safety of heating and moving appliances!
• Protect from moisture, extreme temperatures, impacts, and vibrations!
• Use indoors only; do not expose to sunlight!
• Keep out of reach of children!

Charge the battery when the device displays "LO" - by plugging the device into the socket!

Distinguish between the maximum load of 16 A / 3680 W and the specified inductive load of 2 A / 460 W. For a motor, compressor, or other inductive appliance, observe the lower permissible limit.

Choosing a climate controller

Match the load type to the control method. An AC fan with adjustable voltage and an EC fan with a signal input require different controls. Follow the limitations for the specific model.

Browse ventilation and climate controllers.

GSE temperature and minimum speed controller with 5A outlet is a speed controller for one or more exhaust fans used in indoor growing rooms.

• maintains a constant room temperature
• provides a continuous minimum speed to maintain basic air exchange
• max. current: 5.0A
• max. load: 1150W

Settings range:

• temperature: 20C° to 30C°
• min. speed: off, 20% to 100%

Technical specifications:

• dimensions W x H x D: 75x110x90mm.
• max. current: 5.0A
• max. load: 1150W
• temperature sensor with 2 m cable
• voltage: 230V, 50Hz

Installation:

• Plug the air fan into the outlet (5). Connect the temperature sensor (7), which has a 2 m cable, to the controller and choose a location for the sensor where you want to take the measurement.
• Make sure it is not directly exposed to a heat source or light, to ensure the most accurate measurement of the ambient air. Now plug the controller's plug (6) into an external outlet. The controller initializes, which can take up to 10 seconds; the green power LED (3) flashes, and the fans run at 50% power. After initialization, the green power LED (3) stays on continuously - the controller regulates from this point on.

Instructions:

1. Use the temperature setting button (1) to set the desired temperature, for example, 24°C.
2. Use the second knob to set the minimum speed (2), which should never drop during regulation; for example, we set it to 20%.
3. The minimum speed setting is the most powerful setting and always overrides the temperature setting. If you set the minimum speed setting (2) to OFF, the fan will stop running when the measured temperature is below the set temperature. The minimum speed setting (2) has a 20% startup peak to provide enough power for the fan to run at low speed.
4. The hysteresis is a fixed value of 2°C. Hysteresis is the controlled range of the fan speed. Within these 2°C, the fan speed will change from the lowest point, set by the minimum speed setting (2), to the highest control point, 100% fan speed, depending on the temperature.
5. While the temperature measured by sensor (7) is below your setting (24°C), the minimum speed regulator keeps the fan running at the minimum speed setting (20%). As the temperature rises above 24°C, the temperature LED (4) turns on and the fan speed starts to increase based on the temperature over the next 2°C, up to 100% when it reaches 26°C.
6. Small fans can be adjusted from 0-100%, but with higher power consumption (large fans), the controller operates in semi-variable mode and will automatically switch to 100%, without variable control. The controller stays on until the temperature drops.
7. Warning! Setting a high minimum speed with large fans will cause them to run at 100% due to internal overheating protection! Lower the minimum speed!

Choosing a climate controller

Match the load type and control method. An AC fan with adjustable voltage and an EC fan with a signal input require different controls. Follow the limitations of the specific model.

Browse ventilation and climate controllers.

TechGrow pressure regulator with flow meter and solenoid valve for controlled CO₂ delivery from a compatible cylinder.

• Pressure regulator.
• Pressure gauge and flow meter.
• Solenoid valve for control by a compatible CO₂ controller.

Check the cylinder connection, operating pressure, and the valve’s electrical ratings.

Compatibility and included items

Distinguish between the controller, measuring sensor, and CO₂ delivery actuator. Check which of these are included in the specific offer.

Browse TechGrow controllers and sensors.

GSE Temperature and Minimum Speed Controller 10A is a speed controller for one or more exhaust fans used in indoor grow rooms.

• maintains a constant room temperature
• provides a continuous minimum speed to maintain baseline air exchange
• max. current: 10.0A
• max. load: 2300W

Setting range:

• temperature: 20C° to 30C°
• min. speed: off, 20% to 100%

Technical specifications:

• dimensions W x H x D: 130x92x105mm.
• max. current: 10.0A
• max. load: 2300W
• temperature sensor with 4m. cable
• voltage: 230V, 50Hz

Instructions:

1. Use the temperature setting knob to set the desired temperature, for example 24°C.
2. Use the second knob to set the minimum speed, which should never drop during regulation; for example, we set this to 20%.
3. The minimum speed setting is the strongest setting and always overrides the temperature setting. If you set the minimum speed setting to OFF, the fan will stop running when the measured temperature is below the set temperature. The minimum speed setting has a 20% startup boost to provide enough power for the fan to run at low speed.
4. The hysteresis is a fixed value of 2°C. Hysteresis is the controlled range of fan speed. Within these 2°C, the fan speed changes from the lowest point, set by the minimum speed setting, to the highest control point, 100% fan speed, depending on the temperature.
5. As long as the temperature measured by the sensor is below your setting (24°C), the minimum speed regulator keeps the fan running at the minimum speed setting (20%). When the temperature rises above 24°C, the temperature LED turns on and the fan speed starts increasing based on the temperature over the next 2°C, up to 100% at 26°C.
6. Small fans can be adjusted from 0-100%, but with higher power consumption (large fans), the controller operates in semi-variable mode and automatically switches to 100% without variable control. The controller remains on until the temperature drops.
7. Warning! Setting a high minimum speed with large fans will cause it to run at 100% due to the internal overheating protection! Reduce the minimum speed!

Choosing a climate controller

Match the load type and control method. An AC fan with adjustable voltage and an EC fan with a signal input require different control methods. Follow the limits specified for the specific model.

Browse ventilation and climate controllers.

The TechGrow temperature probe with a 5 m cable measures temperature and sends the reading to a compatible device.

Features and functions

• Measured parameter: temperature.
• Cable length: 5 m.
• Separate sensor, selected according to the controller.

Check whether the specific model requires a TempProbe and whether the probe is included.

Choosing a compatible sensor

Check the controller model, measured parameters, and sensor range. Having the same connector is not sufficient proof of compatibility.

Browse TechGrow controllers and sensors.

TechGrow T-Micro is a CO₂ controller for measuring and managing CO₂ supply via an external compatible sensor.

Features and functions

• CO₂ regulation range: 300–2000 ppm.
• Day and night mode via light detection in the external CO₂ sensor.
• Compatible versions up to 2000 ppm: S-2, S-4, and S-Eco.
• The CO₂ sensor is not included in the controller’s basic offer.

Select the sensor and controlled CO₂ source before ordering. Sensor versions up to 10,000 ppm are not a direct replacement for the specified configuration.

Compatibility and package contents

Distinguish between the controller, measuring sensor, and CO₂ supply actuator. Check which of these are included in the specific offer.

Explore TechGrow controllers and sensors.

Compatible sensors by configuration: TechGrow S-2, CO₂ and light sensor, up to 2000 ppm and TechGrow S-4 2000 ppm, CO₂, temperature and humidity sensor.

The VDL analog timer switches a connected device on and off according to a repeating daily schedule.

Features and functions

• Operating cycle: 24 hours.
• Setting increment: 15 minutes.
• Set using the dial segments.

Check the rated load on the supplied timer's label. Select intervals according to your equipment and plants' needs.

Choosing a timer

Compare daily and weekly programs, the minimum setting increment, and the permitted load. The starting current of a pump, ballast, or LED driver may limit the number of devices you can connect.

Browse analog and digital timers.

Controlling the climate in your grow room with the TechGrow Clima Control Basic Plus 14A is simple yet effective.

• Power supply: 100 to 240V
• Mains frequency: 50 to 60Hz
• Power consumption: 3W (without fan)
• Maximum fan power: 14 Amp / 3400W
• Temperature setting range: 10 - 45°C
• Temperature hysteresis setting range: 1 -7°C
• Probe: pre-installed temperature probe with a 4.5 m cable

Instructions for use here!

Setting up the Clima Control Basic Plus 14A is easy with its convenient rotary knobs. Its unassuming appearance is deceptive, as the Clima Control Basic Plus 14A is equipped with the reliable, advanced TechGrow technology you already know.

The bright green LED display shows the current temperature and setpoint as you adjust the settings.

This controller comes with a pre-installed temperature probe with a 4.5 m cable.

Features:

• Plug & Play
• LED indicator for setpoint and current temperature
• very easy to use
• fan minimum and maximum power can be adjusted
• analog control knobs for easy adjustment of settings
• two fan outlets
• easy to connect
• easy-to-replace fuse
• spare fuse included

Choosing a climate controller

Consider the load type and control method. An AC fan with adjustable voltage and an EC fan with a signal input require different controls. Follow the limitations specified for the particular model.

Browse ventilation and climate controllers.

The LUMii XLED Controller controls compatible LED lighting via a 0–10 V signal.

Features and functions

• One control channel.
• Up to 25 connected LUMii XLEDv6 680 W lights.
• Set the daily photoperiod, dimming, and smooth sunrise and sunset.
• Five-button interface and display.
• Connection via RJ12 or the corresponding terminals. EU power adapter.

The count of up to 25 applies to the specified XLEDv6 configuration. For another light fixture, check the signal, connection, and manufacturer limitations.

Connecting to the lighting

Check the control signal and compatibility of the specific ballast or driver. The control channel and the power supply to the luminaires serve different functions.

Browse lighting controllers.

The G-Systems Timer Box 4 × 600 W is a timer board for switching compatible lighting on and off as a group.

Features and functions

• Lighting configuration: 4 × 600 W.
• Version with a separate heating output when the lights are off.
• The timer sets the switch-on and switch-off times.

Size the power supply and protective devices according to the diagram for the exact version. Check the load on each output and the inrush current of the ballasts or drivers. For the version with heating, check the permitted load of the heating output separately.

Choosing a power board

Check the power supply, total current, and individual output limits. For LED drivers and ballasts, account for inrush current. The number of sockets is not the number of power circuits.

Browse lighting controllers and boards.

The VDL digital timer automates switching a connected electrical appliance on and off according to a set schedule.

Features and functions

• Electronic schedule setting.
• Display for setting the time and schedule.
• Suitable for automating compatible electrical loads within the ratings marked on the device.

Check the exact model, number of programs, minimum interval, and permitted load before choosing. The backup battery, when included, preserves the clock or settings; it does not power the connected electrical appliance during a mains outage.

Choosing a timer

Compare daily and weekly schedules, the minimum interval, and the permitted load. The starting current of a pump, ballast, or LED driver may limit the number of connected devices.

Browse analog and digital timers.

TechGrow - Clima Eco 5A (Minimum speed) controls the minimum speed of your fan until it reaches or maintains the desired temperature in the grow room. This budget-friendly controller is easy to operate - it has just two rotary knobs - for setting the fan's minimum speed and the desired room temperature.

• Controls the fan's minimum speed until the desired temperature is reached or maintained
• Fan minimum speed setting range: 10% - 100%
• Temperature setting range: 15° - 35°C
• Hysteresis: 2°C 
• Minimum required sensor: TempProbe (not included)

Features:

• Controls the fan's minimum speed until the desired temperature is reached or maintained
• LED indicator for a stable climate or high temperature
• The set minimum fan speed and temperature are retained in the event of a power outage
• Fan minimum speed setting range: 10% - 100%
• Temperature setting range: 15° - 35°C
• Hysteresis (not adjustable): 2°C 
• Automatic detection of cable faults or poor sensor connection
• 2 UTP ports
• Easy fuse replacement (includes a spare fuse)
• Minimum required sensor: TempProbe (not included)

Technical specifications:

• Power supply: 100-240V
• Power consumption: 3W
• Fuse: 5A
• Power cable: 3x1.5 mm. / 1.7 m.
• Product dimensions LxHxW: 13x8x7 cm. 
• Product weight: 934 g.
• Box dimensions LxHxW: 25x15x14 cm. 
• Box weight: 1180 g.

The manual, available in 5 languages: here

A separate compatible TempProbe is required for this configuration. Check the included components before placing your order.

Choosing a climate controller

Match the load type and control method. An AC fan with adjustable voltage and an EC fan with a signal input require different controls. Follow the limits specified for the particular model.

Browse ventilation and climate controllers.

The Hager Power Panel 36 × 600 W is a distribution panel for organizing a group of lights and additional loads.

Features and functions

• Configuration designation: 36 × 600 W.
• Constant-power outputs: 8.
• Heating outputs in this configuration: 2.

Constant-power outputs do not indicate the number of independent power circuits. Before choosing, check the power supply, protection devices, and permissible load of each output. Installation and sizing of the power system must be carried out by a qualified electrician.

Choosing a power distribution panel

Check the power supply, total current, and the limits of individual outputs. For LED drivers and ballasts, account for inrush current. The number of outlets is not the number of power circuits.

Browse lighting controllers and panels.

The TechGrow S-4 is a combination sensor that measures CO₂, temperature, and relative humidity and detects light.

Features and functions

• CO₂ range version: up to 2000 ppm.
• Measures CO₂, temperature, and humidity.
• Detects light for day and night mode on a compatible controller.

S-4 is selected according to the controller model and range. The appropriate version of S-4 is required for the combined functions of the T-2 Pro. The sensor is sold separately from the controller.

Choosing a compatible sensor

Check the controller model, the measured parameters, and the sensor range. An identical connector is not enough to prove compatibility.

Browse TechGrow controllers and sensors.

Related models: TechGrow T-2 Pro 7 A, CO₂ and climate controller and TechGrow T-2 Pro 14 A, CO₂ and climate controller.

G-Systems Timer Box 8 × 600 W is a timer board for switching compatible lighting on and off as a group.

Features and functions

• Lighting configuration: 8 × 600 W.
• Version with a separate heating output when the lighting is off.
• The timer sets the on and off times.

Size the power supply and protection devices according to the wiring diagram for the exact version. Check the load on each output and the inrush current of the ballasts or drivers. For versions with heating, check the permitted load on the heating output separately.

Choosing a power distribution board

Check the power supply, total current, and the limits of the individual outputs. For LED drivers and ballasts, account for the inrush current. The number of sockets is not the number of power circuits.

Explore lighting controllers and boards.

TechGrow Clima Control ECO 8A can control up to 2 fans and precisely create the right climate in your room. It ramps up more slowly than other controllers to achieve a more stable climate. The controller is very easy to use - with the rotary knobs, you can easily set the desired temperature and hysteresis, as well as the fan's minimum and maximum speed. The modern software takes care of the rest!

main functions

• controls and displays: temperature
• day/night detection: no
• light sensor: no
• thermostat relay: no
• temperature alarm: no

software functions

• temperature range: 10 - 45°C
• temperature hysteresis: 0 - 7°C
• temperature settings: day
• humidity settings: no
• day/night delay: no
• min./max. values: no

power supply

• power supply: 100 - 240V
• consumption: 3W
• fuse: 8A
• max. load: 1700W
• Power cable: 3 x 1.5 / 1.7m

The fans are automatically adjusted according to the settings. Once you set the desired temperature, Clima Control Eco 8A will always maintain that temperature. When the temperature exceeds the “set point + hysteresis,” the fan speed will slowly increase. When the temperature falls below the “setting - hysteresis,” the fan speed will slowly decrease. If desired, the controller settings can be temporarily overridden to allow the fans to run at full speed (100%). 

Instructions for use: here*

Features:

• Plug and Play (simply connect it to the power supply and switch it on).
• Easy to use.
• Temperature adjustment range: 10 - 45°C
• Temperature hysteresis adjustment range: 1 - 7°C
• Connected temperature sensor with 4.5m cable.
• Rotary knobs for easy adjustment of settings.
• Suitable for connecting 2 fans.
• Option for continuous full fan speed (100%).
• Easy fuse replacement.
• Spare fuse (included).
• Not compatible with other sensors or devices.

Choosing a climate controller

Consider the load type and control method. An AC fan with adjustable voltage and an EC fan with a signal input require different controls. Follow the limits specified for the specific model.

Browse ventilation and climate controllers.

TechGrow Day/Night Fan Controller 7A is the easiest-to-use climate control device for your indoor garden. The controller is highly efficient and completely 'plug & play' (simply connect it to the mains and switch it on). To adjust the day and night fan speeds, use the two rotary knobs; the settings will switch automatically thanks to the built-in light sensor.

main features:

• controls: fan speed
• display: no
• day/night detection: yes
• light sensor: yes, built-in
• thermal relay: no
• temperature alarm: no

power supply:

• input voltage: 100 - 220V
• power consumption: 3W
• fuse: 8A
• triac: 12A
• power cable: 3 x 0.75 / 1.7m

Note: cannot be connected to a sensor!

Instructions for use: here*

The controller cannot be connected to a temperature sensor!

Main features:

• Plug and Play (simply connect it to the mains and switch it on).
• Easy to use.
• Day and night mode speed settings.
• Built-in light sensor for automatic switching between day and night mode.
• Analog rotary knobs for easy adjustment of the settings.
• Continuous mode with 100% fan capacity (full speed).
• Easy-to-replace fuse.

Dimensions and weight:

• product dimensions H/W/D: 21 x 24 x 10cm
• product weight: 1167g
• packaging dimensions H/W/D: 25 x 29 x 17cm
• weight with packaging: 1583g

The day and night speeds switch based on light detection. This function is different from regulation based on measured temperature.

Choosing a climate controller

Consider the load type and control method. An AC fan with adjustable voltage and an EC fan with a signal input require different controls. Follow the limitations of the specific model.

Browse ventilation and climate controllers.

Make watering your garden easy as child's play with the Water Master irrigation timer! Setting the timer takes just 2 easy steps - turn the Run Time dial to set your desired watering duration, and the Frequency dial to set the desired interval between waterings. Then connect it to your garden hose using a standard quick connector, and the timer will take care of the rest!

• uses an efficient solenoid valve
• up to 8 waterings per day
• programs the frequency and watering duration
• quick and easy to install on any tap

Technical specifications:

• Frequency (Frequency / Frequency): you can set watering every 1, 2, 3, 4, 6, 8, 12, 24, 48, 72 hours or 1 week
• Run time / watering (Active time / Runtime): 1, 3, 5, 10, 15, 20, 30, 60, 90, or 120 minutes
• Connections: ¾ male and ¾ female connector
• Batteries: 2 x AAA (not included)

Before setting the watering schedule

Take the inlet pressure, water source, and watering duration into account. Check the amount delivered with a test cycle.

Browse irrigation timers and ready-made irrigation systems.

The Hager Power Panel 32 × 600 W is a distribution board for organizing a group of lights and additional loads.

Features and functions

• Configuration designation: 32 × 600 W.
• Continuously powered outputs: 8.
• Heating outputs in this configuration: 2.

The continuous outputs do not indicate the number of independent power circuits. Before choosing, confirm the power supply, protection devices, and permissible load for each output. Installation and sizing of the power system must be carried out by a qualified electrician.

Choosing a power distribution board

Check the power supply, total current, and individual output limits. For LED drivers and ballasts, account for inrush current. The number of outlets is not the number of power circuits.

Browse lighting controllers and boards.

G-Systems Timer Box 6 × 600 W is a timer board for switching compatible lighting on and off as a group.

Features and functions

• Lighting configuration: 6 × 600 W.
• Version for timer-controlled lighting.
• The timer sets the on and off times.

Size the power supply and protection devices according to the wiring diagram for the exact version. Check the load on each output and the inrush current of the ballasts or drivers. For versions with heating, check the permitted load on the heating output separately.

Choosing a power distribution board

Check the power supply, total current, and the limits of the individual outputs. For LED drivers and ballasts, account for the inrush current. The number of sockets is not the number of power circuits.

Explore lighting controllers and boards.

Water Master is a high-quality digital irrigation timer, designed specifically to control drip irrigation and sprinkler irrigation systems. 

• uses an efficient solenoid valve
• up to 8 watering cycles per day
• programming of frequency and watering duration
• easy and quick to install on any tap

Specifications:

• Connections: ¾ male and ¾ female connector
• Batteries: 2 x AAA (not included)

Before setting up the watering schedule

Take into account the inlet pressure, water source, and watering duration. Check the amount of water delivered with a test cycle.

Explore timers and ready-made irrigation systems.

TechGrow - Clima Micro Day/Night Fan Controller 5A is a controller that regulates your fan speed using two operating modes - day and night. You can easily set the desired speed using the rotary knobs, as well as a delay time of 0 to 10 minutes. The controller does not connect to a sensor and does not measure CO2, temperature, or humidity!

• Very easy to use
• Adjustable fan speed for day and night modes
• Adjustable delay time of up to 10 minutes
• Built-in light sensor

Features:

• 100% plug & play (connect to the power supply and switch on)
• Very easy to use
• Adjustable fan speed for day and night modes
• Adjustable delay time of up to 10 minutes
• Built-in light sensor
• Analog rotary knobs for easy adjustment of settings
• Easy fuse replacement (includes a spare fuse)
   

Technical specifications:

• Power supply: 100-240V
• Power consumption: 3W
• Fuse: 5А
• Power cable: 3x1.5мм. / 1.7м.
• Product dimensions LxHxW: 13х8х9см. 
• Product weight: 660гр.
• Box dimensions LxHxW: 25х15х14см. 
• Box weight: 906гр.

Day and night speeds switch according to light detection. This is different from adjusting based on measured temperature.

Choosing a climate controller

Consider the load type and control method. An AC fan with adjustable voltage and an EC fan with a signal input require different control methods. Follow the limitations of the specific model.

Browse ventilation and climate controllers.

Step-down transformer that lets you control fans without the low-frequency noise at low speed.

The six control settings help you better control the exhaust fan according to the temperature and humidity settings you have selected.

The four buttons let you set the temperature, temperature hysteresis, humidity and humidity hysteresis.
Using the built-in jumper - J1 (in the box), you can choose whether the fan continues running at minimum speed or stops when the desired temperature and humidity are reached. When J1 is closed, ventilation continues at minimum speed. When it is open, the fan stops completely.

It comes with a 4m cable with a temperature and humidity sensor, an exhaust fan outlet and a waterproof enclosure.

- temperature range: 20C° - 30C°
- temperature hysteresis: 2C°-8C°
- humidity range: 30% - 100%
- humidity hysteresis: 6%-30%
- dimensions: 265mm х 300mm х 205mm
- maximum current: 2,5 A
- Voltage: 230V / 50HZ
- Digital sensor 5V measures temperatures from –55°C to +125°C (–67°F to +257°F)
- Accuracy: 0,5C° in the range from -10C° to +85C°; ±4,5%rh
- Protection rating: IP54
 

Choosing a climate controller

Consider the load type and control method. An AC fan with adjustable voltage and an EC fan with a signal input require different controls. Follow the limitations of the specific model.

Browse ventilation and climate controllers.

TechGrow T-Nano CO₂ Controller ECO  is a powerful and easy-to-use CO₂ controller from TechGrow's budget ECO range. T-Nano takes extremely accurate measurements, regardless of the size of your indoor growing space - from small tents to very large spaces. When connected to the TechGrow S-4 sensors, T-Nano can facilitate connection to another TechGrow controller.

main features:

• controls: CO₂
• measures: CO2
• PPM range: 300 - 2000ppm
• day/night detection: yes
• light sensor: in the CO₂ sensor

power supply:

• input current: 100/240V, 50/60 Hz
• CO₂ output power: 100 – 220V
• power consumption: 3W
• CO₂ relay: 8A
• CO₂ fuse: 4A
• power cable: 3 x 0.75 / 1.7m

Note: the sensor is sold separately!

Instructions for use: here*

T-Nano can be used to facilitate connection to another TechGrow controller and display the readings from connected CO₂, RH, and temperature sensors (provided it is connected to the TechGrow S-4 sensors).
To set the desired CO₂ concentration or hysteresis, use the two rotary knobs and leave the rest to the controller. The LEDs indicate when CO₂ is being dispensed, whether the climate is stable, and whether the relay is off, for example, during night mode.
T-Nano is fully compatible with many TechGrow products. We recommend using the TechGrow S-ECO sensor with this controller.

Recommended sensor: TechGrow S-ECO 0/2000 ppm

Compatible sensors:

1. TechGrow S-ECO 0/2000 ppm
2. TechGrow S-2 0/2000 ppm
3. TechGrow S-4 0/2000 ppm

Main features:

• Plug and Play (simply connect it to the power supply and turn it on).
• Suitable for use in small and large spaces/rooms.
• LEDs indicate when CO₂ is being dispensed.
• Switches the CO₂ source (CO₂ burner or CO₂ cylinder) on or off via a 230V relay.
• Automatically saves the preset settings in the event of a power outage.
• The external sensor has a light sensor that enables automatic switching between day and night modes.
• Automatic detection of cable faults or poor connection with the sensor(s)
• The sensor is connected via a standard UTP network cable (included).
• The various sensors are sold separately!
• Can be connected to a TechGrow Datalogger (DL-1).

Dimensions and weight:

• product dimensions H/W/D: 15 x 13 x 8 cm 
• product weight: 590 g
• packaging dimensions H/W/D: 16 x 26 x 15 cm 
• weight with packaging: 920 g

Compatibility and package contents

Distinguish between the controller, the measuring sensor, and the CO₂ delivery actuator. Check which of these are included in the specific offer.

Browse TechGrow controllers and sensors.