pH & EC Meters

GHE pH Test Kit 60ml is a liquid pH tester, ideal both for easy testing and for backup or supplementary measurement after using a digital pH meter.

• Quick, reliable, accurate pH testing without batteries
• testing range: from 4.0 to 8.5
• capacity for up to 1000 tests

How to use:

1. simply fill the supplied test tube halfway with the prepared nutrient solution
2. add two drops of the liquid pH tester
3. shake and compare the resulting colour with the chart to read the pH level.

liquid pH test - accuracy 0,2

Easy-to-use, affordable and economical test for the acidity of the working solution.

Pour the solution to be measured into the supplied test tube. Add a few drops of the indicator solution and shake. Read the pH according to the colour on the scale.


contains 30ml, sufficient for 150 measurements
pH range 5.6-7.4, reading accuracy 0,2

PH600 is a digital pen for measuring the pH of liquids from Milwaukee's economy range of measuring instruments. It is ideally suited to enthusiasts of hydroponics and aquariums.

• Fast and accurate results with a digital LCD display.
• Easy measurement - simply place the probe in the water, stir gently and wait for the reading to stabilise.
• Easy one-point calibration with an easy-to-use trimmer located on the back of the pH tester for protection from accidental splashes.
• Cap for protecting the pH sensor, keeping it wet when stored upright.
• Low power consumption for extended battery life (batteries included).

Instructions for use here*. Calibration instruction video here*.

The set includes:

• 1x Milwaukee PH600 Digital pH Pen - digital pH measurement pen
• 1x calibration screwdriver

Technical specifications:

• measurement range: 0.0 - 14.00 pH
• resolution: 0.1 pH
• measurement accuracy: 0.1 pH
• calibration: manual, single-point
• operating environment: temp. 0 - 50°C, humidity up to 95%
• batteries: 3x LR44 1.5V (included)
• battery life: up to 700 h of operation
• dimensions: 32 x 180 x 65 mm
• weight: 60 g
• device warranty: 1 year
• sensor warranty: 6 months

Proper maintenance of your pH meter will give you fast and accurate results for longer. Here are our four best tips:

1. Always store it with the cap filled with buffer or MA9015 storage solution, and not water.
2. Clean the pH sensor regularly by soaking it in MA9016 cleaning solution.
3. Calibrate after cleaning and/or storage before testing to correct changes in the pH sensor.
4. Stir the sample gently with the pen for a faster result.

CD611 is a digital pen for measuring electrical conductivity (EC) of liquids from Milwaukee's economical range of measuring instruments. Suitable for hobby gardeners who want to ensure their plants receive the right amount of nutrients.

• Measures conductivity and temperature with automatic temperature compensation
• Ideal range for hydroponics (0 to 20 000 µS/cm)
• The measurement units in µS/cm can easily be converted to ppm
• Factory calibrated with the option to recalibrate when needed

Instructions for use here*. Calibration instruction video here*.

The set includes:

• 1x Milwaukee CD611 Digital Conductivity Pen (EC) - digital pen for measuring electrical conductivity (EC)
• 1x calibration screwdriver

Features:

• measurement range: 0 to 20 000 µS/cm
• resolution: 100 µS/cm
• measurement accuracy: ±2% full scale
• temperature compensation: automatic, from 5 to 50°C, with ß=2%/°C
• calibration: manual, single-point
• operating environment: temperature 0 to 50°C, humidity 95%
• batteries: 4x LR44 1.5V alkaline (included)
• battery life: up to 350 h of operation
• dimensions: 32 x 180 x 65 mm
• weight: 60 g

Maintenance: EC electrodes can develop nutrient build-up over time. To minimise build-up, always rinse the probe in fresh tap water after each use!.

EC to TDS conversion: Milwaukee EC Pen, like all conductivity meters, measures electrically charged ions in a solution and provides an absolute measure of conductivity. EC is often converted to TDS in parts per million (ppm). Different scales include the 500 scale, 650 scale and 700 scale. However, true PPM can only be determined through chemical analysis. Your mS/cm reading can be approximately converted to TDS (ppm), as shown in the examples below.

1. 2.00 mS/cm = 2000 µS/cm = 1000 ppm on the .50 factor scale
2. 2.00 mS/cm = 2000 µS/cm = 1400 ppm on the 442 scale or .70 factor scale

Milwaukee pH51 is one of the most accurate, robust and reliable budget pH testers on the market. The easily replaceable probe provides years of worry-free use. Ideal for use in hydroponics, aquariums, gardening, pools and many other applications.

• fast and easy-to-read results with a large digital LCD display
• measurement accuracy: ±0.1 pH
• measurement range: 0.0 - 14.0 pH
• easy calibration: 1-point or 2-point
• completely waterproof (IP65)
• built-in probe: MA73600 (replaceable)

Instructions for use here*. Calibration instruction video here*.

The set includes:

• 1x calibration solution pH 7.01 - 20ml
• 1x calibration solution pH 4.01 - 20ml
• 1x calibration screwdriver

Key features:

• measurement range: 0.0 - 14.0 pH
• resolution: 0.1 pH
• measurement accuracy: ± 0.1 pH
• easy manual 1-point or 2-point calibration.
• built-in probe: MA73600 (replaceable)
• operating conditions: 0 - 50°C; max. RH (relative humidity) 100%
• batteries: 3x 1.5V, IEC LR44, A76 (included)
• battery life: over 1500 h of continuous use
• batteries: included in the package
• dimensions: 16.5 cm , ⌀ 3 cm
• weight: 99 g
• instrument warranty: 1 year
• probe warranty: 6 months

Calibration:

1. Unscrew the battery-compartment cap at the top of the meter and follow this two-point calibration procedure:
2. Immerse the electrode in pH 7.01 calibration buffer solution.
3. Allow the reading to stabilise, then use a small screwdriver to turn the “7” calibration trimmer in the battery compartment until the display shows “7.0”.
4. Rinse the electrode with tap water and immerse it in pH 4.01 calibration buffer solution.
5. Allow the reading to stabilise, then use a small screwdriver to turn the “4” calibration trimmer until the display shows “4.0”.

Proper probe maintenance will give you fast, accurate results for longer. Here are our top four tips.

1. Always store it with the cap filled with buffer or MA9015 storage solution, and not water.
2. Clean your probe regularly by soaking it in MA9016 cleaning solution.
3. Calibrate after cleaning and/or storage before testing to correct changes in the pH and EC sensor.
4. Gently stir the probe in the sample for a faster result.

Milwaukee Waterproof pH55 PRO pH/Temp is one of the best-selling pH testers on the market. Accurate measurements, affordability, robustness and reliability make it one of the preferred instruments among hobbyists and professional growers alike. With a large digital LCD display, an easily replaceable probe and an extended pH measuring range, ph55 PRO meets almost every application. Ideal for use in aquariums, hydroponics, gardening, swimming pools, beer brewing and many other applications.

• accuracy to ±0.1 pH and extended measuring range from -2.0 to 16.0 pH
• lightweight and portable
• easy to use
• automatic temperature compensation (ATC)
• easy automatic calibration at one or two points
• includes 2x solutions for calibration (M10007 and M10004)
• completely waterproof (IP65)
• built-in probe: Mi56P (replaceable)

Milwaukee EC meter EC60

Professional EC meter

Professional waterproof EC meter with temperature display, automatic temperature compensation and automatic calibration.

Displays EC or PPM, plus solution temperature.

"HOLD" function for storing the measured value.

Replaceable sensor.

Milwaukee EC meter EC60

• Range: 0-20 mS/cm; 0-10 ppt; 0.0 - 60.0°C
• Resolution: 0.01 mS/cm; 0.01 ppt; 0.1°C
• Accuracy: ±2%; ±0.5°C
• Calibration: automatic, one point
• Automatic temperature compensation with β=0.0 to 2.4%/°C
• Operating conditions: temp. 0-50°C, humidity up to 100%
• Batteries: 4 pcs. LR44 1,5V / 100 hours of operation
• Automatic shut-off: after 8 min.
• Dimensions: 200 x 38 mm / 100 g
• Manufacturer's warranty - 2 years for the device, 6 months for the sensor. Does not apply to mechanical damage and improper use!

Take quick pH and temperature measurements of your solution with the Bluelab pH pen!

• completely waterproof
• simple two-point calibration
• 1-year warranty
• automatic shut-off function to extend battery life
• 1 x AAA alkaline battery (included)
• pH measurement range: 0.0 - 14.0 
• accuracy: ± 0.1 at 25°C 

Full technical product specifications here!

The best, most convenient solution for measuring the pH and temperature of your nutrient solution! Plants obtain their nutrients from minerals, but they can receive all the minerals they need only when certain conditions are right. Think of nutrients as a lock. pH is the key. A key factor affecting nutrient uptake is whether your solution is acidic or alkaline. We measure this through pH. The Bluelab pH pen also measures the temperature of the solution, as root health is vital to a successful harvest. Temperature affects the growth rate and structure of the plant, so a solution temperature of 18-22°C is recommended. The Bluelab pH pen offers a compact, quick and convenient way to manage your crop's success and ensure maximum nutrient uptake. Together with the Bluelab Conductivity Pen, you have a convenient, accurate system for ensuring optimal plant growth and health.

• completely waterproof
• simple two-point calibration
• 1-year warranty
• automatic shut-off function to extend battery life
• 1 x AAA alkaline battery (included)
• pH measurement range: 0.0 - 14.0 
• temperature: 0 - 50°C
• accuracy: pH: ± 0.1 at 25°C
• selectable temperature units (C°/F°)
• Backlit LCD display
• built-in pH probe (non-replaceable)
• tick indicating successful calibration
• hold function for recorded measurements
• low battery indicator
• automatic shut-off function

Milwaukee C66 is one of the most reliable budget testers for measuring conductivity (EC) and solution temperature on the market. Designed for growers who want to ensure their plants receive the right amount of nutrients. By maintaining EC levels within the target range, you will achieve better results.

• measures conductivity (EC) and temperature with automatic temperature compensation (ATC)
• measurement range: 0.0 - 10.00 mS/cm
• measurement accuracy: ±2%
• measurement units mS/cm, which can easily be converted to ppm (parts per million)
• factory calibrated with the option to recalibrate (if necessary)
• completely waterproof (IP65)
• built-in electrode: MA73076 (replaceable)

Instructions for use here*. Calibration instruction video here*.

The set includes:

• 1x 1413 µS/cm calibration solution - 20 ml
• 1x calibration screwdriver

Technical specifications:

• measurement range: 0.00 - 10.00 mS/cm
• resolution: 0.01 mS/cm
• measurement accuracy: ±2%
• calibration: manual, 1-point
• operating environment: 0 - 50°C; max. RH (relative humidity) 100%
• batteries: 3x 1.5V, IEC LR44, A76 (included)
• battery life: over 250 hours
• batteries: included in the set
• dimensions: 16.5 cm , ⌀ 3 cm
• weight: 99 g
• instrument warranty: 1 year
• electrode warranty: 6 months

Calibration:

1. Immerse the measuring instrument in 1413 µS/cm calibration solution.
2. Unscrew the battery-compartment cap on the top of the measuring instrument.
3. Allow the reading to stabilise, then use a small screwdriver to turn the calibration trimmer inside the battery compartment until the display shows “1.41”.
4. Fit the battery-compartment cap.
5. Calibration is complete.

Maintenance: EC electrodes can develop nutrient buildup over time. To minimise buildup, always rinse the probe in fresh tap water after each use!.

EC to TDS conversion: Milwaukee EC Pen, like all conductivity meters, measures electrically charged ions in a solution and provides an absolute measure of conductivity. EC is often converted to TDS in parts per million (ppm). Different scales include the 500 scale, 650 scale and 700 scale. However, true PPM can only be determined through chemical analysis. Your mS/cm reading can be approximately converted to TDS (ppm), as shown in the examples below.

1. 2.00 mS/cm = 2000 µS/cm = 1000 ppm on the .50 factor scale
2. 2.00 mS/cm = 2000 µS/cm = 1400 ppm on the 442 scale or .70 factor scale

Take quick measurements directly in your plants' soil quickly and easily with the Bluelab Soil pH pen!

Bluelab Soil pH pen is a meter for measuring pH and soil temperature in soil and other growing media. With this smart pen, you can be sure that your plants receive the right nutrients. It can also measure liquids... Convenient, isn't it?

• completely waterproof
• effective in most growing media and in water / solution
• 1-year warranty
• simple two-point calibration
• automatic shut-off function to extend battery life
• 1 x AAA alkaline battery (included)
• pH measurement range: 0.0 - 14.0
• accuracy: ± 0.1 at 25°C 

Measuring soil pH and temperature—the essentials of growing.

• All plants need a balanced diet of nutrients (food) to grow. However, plants can access nutrients only if the pH (potential hydrogen) of your growing medium falls within the correct range.
• Contrary to common belief, all growers should measure pH, whether growing in soil or solution. This is because pH plays an important role in making nutrients soluble so they can be absorbed by plants. If your medium is too alkaline or too acidic, your plants will not be able to obtain all the nutrients they need. Temperature is also important, as it can affect the structure and growth rate of your plants.
• Together with the Bluelab Conductivity Pen, you have a convenient, accurate system for ensuring optimal plant growth and health.

Product information: here*

Instructions for use: here*

With the Milwaukee Pocket Mi6000 set, you can monitor the temperature, pH and electrical conductivity (EC) levels of your plants' nutrient solution. The set includes:

• 1x digital pH tester pen Milwaukee pH600
• 1x digital EC tester pen Milwaukee CD611
• 1x hard plastic storage case

Bluelab Nutrient Meter is designed for hydroponically grown crops that require a higher-than-normal EC or CF level (electrical conductivity or nutrient-solution concentration) during their growing cycle.

• completely waterproof
• The 40.7cm length enables convenient stirring of the nutrient solution directly in the reservoir!
• No calibration required (factory calibrated)!
• Provides measurements on EC, CF, ppm700 and ppm500 scales
• Automatic on/off function
• 5-year warranty
• EC measurement range: 0.2 - 3.6
• EC measurement accuracy: ± 0.1 at 25°C

Full product technical specifications here!

When growing hydroponically, it is essential to KNOW the strength of the nutrient solution before giving it to your plants. If conductivity readings are too low, your plants may not receive enough nutrients. If readings are too high, plants can become dehydrated. To take a measurement, simply place the probe in the solution and the reading will be indicated by the flashing lights.

?  The Milwaukee Pocket Tester Kit (pH51 and EC66) is ideal for fast and accurate measurement of pH and electrical conductivity (EC) in various environments, including hydroponics, aquariums, swimming pools and laboratories. The kit includes two portable and waterproof testers with LCD displays, ensuring easy use and reliable results.

? Detailed specifications:

pH51 – pH Tester:

• Measurement range: 0.0 – 14.0 pH
• Resolution: 0.1 pH
• Accuracy: ±0.1 pH
• Calibration: Manual, two-point (pH 4.01 and pH 7.01)
• Electrode: Replaceable MA73600 with double junction
• Water resistance: IP65
• Temperature range: 0 to 50°C
• Battery: 3 x 1.5V (included), battery life over 1500 hours
• Dimensions: 165 x 30 x 30 mm
• Weight: 80 g

EC66 – Electrical Conductivity (EC) Tester:

• Measurement range: 0.00 – 10.00 mS/cm
• Resolution: 0.01 mS/cm
• Accuracy: ±2% of full scale
• Calibration: Manual, one-point (1413 µS/cm)
• Temperature compensation: Automatic (5 to 50°C)
• Electrode: Replaceable MA73076
• Water resistance: IP65
• Battery: 3 x 1.5V (included), battery life approximately 250 hours
• Dimensions: 165 x 30 x 30 mm
• Weight: 80 g

 Kit contents:

• 1 x pH51 pH Tester
• 1 x EC66 Electrical Conductivity Tester
• 1 x Calibration kit (pH 4.01, pH 7.01 and 1413 µS/cm solutions)
• 1 x Small calibration screwdriver
• 1 x Protective storage case

✅ Benefits of use:

• Fast and accurate measurements: Easy to use with quick results.
• Suitable for various applications: Ideal for hydroponics, aquariums, swimming pools and laboratories.
• Waterproof and durable: Suitable for use in various conditions.
• Easy maintenance: Replaceable electrodes and long battery life.

Take quick EC and temperature readings of your solution with the Bluelab Conductivity pen!

• completely waterproof
• simple one-point calibration
• 1-year warranty
• automatic shut-off function to extend battery life
• 1 x AAA alkaline battery (included)
• measurement range EC: 0.0 - 10.0
• accuracy: ± 0.1 at 25°C

Full product technical specifications here!

This Bluelab EC pen simply shows whether your plants are receiving the right amount of nutrients and lets you know if any adjustments to the solution are required. To feed your plants well, you need to know what you are feeding them! Measuring conductivity every day is the best way to avoid over-diluting or over-concentrating your nutrient solution. Replace the reservoir solution completely every 7 days. Top up nutrient levels between changes so your plants always have the food they need. Bluelab Conductivity Pen also measures solution temperature, as root health is vital to a successful harvest. Temperature affects the rate of growth and plant structure, so a solution temperature of 18-22°C is recommended.

• completely waterproof
• simple one-point calibration
• 1-year warranty
• automatic shut-off function to extend battery life
• 1 x AAA alkaline battery (included)
• measurement range EC: 0.0 - 10.0
• accuracy: ± 0.1 at 25°C
• Selectable conductivity and temperature units (EC/ppm,C°/F°)
• Backlit LCD display
• Tick mark indicating successful calibration
• Measurement hold function
• Low battery indicator

professional pH monitor for continuous use

pH monitor for continuous monitoring of hydroponic or fertiliser solutions, aquariums and aquaponic systems, swimming pools and more. Convenient visual indication function when the pH of the solution crosses a set value (up or down, selectable by knob). Manual calibration at 2 fixed points – pH 4 and pH 7.

Separately connectable sensor, compatible with pH monitors from other manufacturers.


range: pH from 0.0 to 14.00
pH indication adjustment range: 3.5 - 7.5
resolution: 0.1 pH
accuracy: ±0.2pH
calibration: manual, at two points (at pH 4 or 10, 7)
LED indication when set values are crossed
set includes: 12V power adapter; electrode with 2m cable; pH 7 calibration liquid.
Dimensions: 149 x 83 x 32 mm; 160g
Manufacturer's warranty – 2 years for the device, 6 months for the sensor. Does not apply to mechanical damage and improper use!

Automate pH control of your solution with the Milwaukee MC122 PRO pH Controller!

The Milwaukee MC122 PRO pH Controller automatically monitors and finely adjusts pH levels. Simply set your pH parameters and let the MC122 PRO do the rest. Recommended for hydroponic plant cultivation or aquariums.

• pH measurement accuracy: pH: ± 0.2 with two-point manual calibration
• control range: from 5.5 to 9.5 pH with alarms activated when readings are above or below the set value
• pH electrode: MA911B/2  (included)
• compatible with dosing pump Milwaukee MP810 1.5 L/h (25 ml/min) (not included)
• device warranty: 2 years
• pH probe warranty: 6 months

Instructions for use here.

• pH measurement accuracy: pH: ± 0.2 with two-point manual calibration
• control range: from 5.5 to 9.5 pH with alarms activated when readings are above or below the set value
• pH electrode: MA911B/2  (included)
• compatible with dosing pump Milwaukee MP810 1.5 L/h (25 ml/min) (not included)
• operating environment: 0–50°C; max. 95% RH
• power supply: 12 VDC adapter  (included)
• mounting kit: included
• dimensions: 15 x 8 x 3.4 cm
• weight: 180 g

You can extend the life of your pH electrode as follows:

1. Storage: The pH probe must be kept hydrated. Long periods of dry storage will harm the probe's sensitivity. Allowing the probe to dry may also cause deposits and clogging at its tip. Storing it in MA9015 storage solution or pH calibration buffers will help address both issues. Do not store in tap water or distilled water! This will damage the probe's sensitivity. The best way to store the probe is with the probe cap filled with storage solution or calibration buffer and the cap tightened to prevent leakage. It is also recommended that the electrode be stored upright to further reduce the potential for leakage.
2. Cleaning: Deposits on the probe tip from the mineral salts of the nutrient solution or from organic material can affect its sensitivity and clog it. We recommend regularly soaking your electrode in MA9016 cleaning solution.
3. Calibration: the glass tip of the pH probe becomes less sensitive over time, so make sure you calibrate regularly to keep your Milwaukee MC122 PRO pH Controller accurate. Also calibrate after cleaning or a long period of storage.

ACCURATE. SIMPLE. RELIABLE. 24 HOURS / 7 DAYS A WEEK pH/EC/ temperature monitoring.

Milwaukee MC811 MAX pH/EC/Temp Monitor lets you monitor pH/TDS/Temp levels automatically 24/7! Simply calibrate the parameters and let the MC811 MAX do the rest. The Milwaukee pH/EC/Temp monitor is preferred by people who want continuous visibility of their pH and nutrient levels 24 hours a day, 7 days a week. Common applications include nutrient reservoirs, hydroponic systems and aquariums. The monitor offers: measurement range: 0.0 - 12.0

• pH / 0.00 - 5.00 mS/cm EC / -10.0 to 60.0°C  measurement accuracy: ± 0.2 pH / ±
• 2% EC / 0.3°C temp. resolution: 0.1 pH / 0.01 mS/cm / 
• 0.1°C easy calibration: 2-point (pH)
• and 1-point (EC), manual quick and easy-to-read results, thanks to
• 3 large LCD displays pH probe MA911B/2 (included in the set)
• Simply calibrate the parameters and start

monitoring 24/7! Instructions for use here. Milwaukee

MC811 MAX pH/EC/Temp Monitor

offers: pH measurement accuracy: pH: ± 0.2

• (with a measurement range of 0 -12.0 pH) EC measurement accuracy: EC: ±
• 2% (at full EC scale) Easy two-point pH calibration
• and one-point EC calibration pH probe MA911B/2
• (included in the set) for easy maintenance and high performance. 2
• m pH probe cable 12
• VDC power supply
• dimensions: 160 x 110 x 35
• mm weight: 560
• g device warranty: 2 years
• pH probe warranty: 6 months You

can extend the life of your pH electrode as follows:

1. Storage: The pH probe must be kept hydrated. Long periods of dry storage will harm the probe's sensitivity. Allowing the probe to dry out can also cause deposits and blockages at its tip. Storing it in MA9015 storage solution or pH calibration buffers will help address both issues. Do not store in tap water or distilled water! This will damage the probe's sensitivity. The best way to store the probe is with the probe cap filled with storage solution or calibration buffer and the cap tightened to prevent leakage. It is also recommended to store the electrode upright to further reduce the risk of
2. leakage. Cleaning: Deposits on the probe tip from nutrient-solution mineral salts or organic material can affect its sensitivity and clog it. We recommend regularly soaking your electrode in MA9016 cleaning solution. Calibration: the
3. glass tip of the pH probe becomes less sensitive over time, so make sure you calibrate regularly to keep your MAX monitor accurate. Also calibrate after cleaning or a long period of storage.

Bluelab OnePen is an "all-in-one" meter that simplifies your daily measurements. It lets you measure acidity (pH), conductivity (EC / PPM), total dissolved solids (TDS) and the temperature of your nutrient solution. Once connected to the Edenic App, you can remotely monitor recorded readings via your smartphone or desktop computer.

• replaceable sensor and its status indicator
• accurate measurements, with resolution up to 0.01 pH
• simultaneously displays recorded pH and EC readings on the display
• measures conductivity in EC, CF, PPM 500 (TDS) or PPM 700
• measures temperature in C° and F° scales
• dust- and waterproof (IP68)

The set includes:

• 1x Bluelab OnePen with replaceable pH, conductivity (EC) and temperature sensor
• 1x 20 ml sachet pH 7.0 Bluelab calibration solution
• 1x 20 ml sachet pH 4.0 Bluelab calibration solution
• 1x 20 ml sachet KCl Bluelab storage solution
• 1x sensor cleaning brush for Bluelab sensor
• 2x AAA batteries

Warranty:

• 2 years for the meter
• 6 months for the sensor
• Proof of purchase is required. For full terms and conditions, visit bluelab.com/product-warranty

Technical specifications:

• pH measurement range: 0.0 - 14.0 pH
• pH resolution: 0.01 pH
• measurement accuracy at 25°C / 77°F (pH): ± 0.05 pH
• pH calibration: two-point, at 7.0 and 4.0 or 10.0
• conductivity measurement units: EC, CF, ppm500 (TDS), ppm700, mS/cm
• conductivity measurement range: 0 - 10.0 EC, 0 - 100 CF, 0 - 5000 ppm 500 (TDS), 0 - 7000 ppm (EC x 700), 0 - 10.0 mS/cm
• conductivity resolution: 0.01 EC, 0.1 CF, 10 ppm500 (TDS), 10 ppm700, 0.01 mS/cm
• measurement accuracy at 25°C / 77°F (conductivity): ±0.1 EC, ±1 CF, ±50 ppm500 (TDS), ±70 ppm700, ±0.1 mS/cm
• conductivity calibration: factory calibrated
• temperature measurement units: °C, °F
• temperature measurement range: 0 - 50°C, 32 - 122°F
• temperature resolution: 0.1
• measurement accuracy at 25°C / 77°F (temperature): ±1
• temperature calibration: not required (factory calibrated)
• temperature compensation: yes
• operating environment:  0 - 50°C / 32 - 122°F (do not use or store outside this temperature range), dust- and waterproof (IP68)
• power supply: 2 x AAA alkaline batteries (included)
• certifications: CF, FCC, IC, UKCA. Contains Bluetooth module IC:8017A-MDBT50Q, FCC ID: SH6MDBT50Q 
• signal range (indoors / urban environment / outdoors): 10 metres
• radio signal: Bluetooth: 5 (low energy)
• system requirements (Edenic App): Android (8.0 or later) or iOS (12 or later)

Milwaukee Pocket tester kit (pH55 and EC60) is ideal for measuring pH, electrical conductivity (EC/TDS) and temperature (°C/°F) in your plants' nutrient solution. The kit includes:

• 1x waterproof pH meter Milwaukee pH55
• 1x waterproof EC meter Milwaukee EC60
• 1x calibration solution Milwaukee pH 4.01 20ml
• 1x calibration solution Milwaukee pH 7.01 20ml
• 1x calibration solution Milwaukee 12880 µS/cm (EC) 20ml
• 1x storage case

This combined 3-in-1 meter lets you measure pH, EC (electrical conductivity) and TDS (total dissolved solids) with one meter and a single probe! Designed for growers

using hydroponics, aquaponics and greenhouses, Milwaukee MW802 PRO is exceptionally robust and easy to use – with one probe, a large screen and easy calibration. The meter’s robust construction and sturdy yet replaceable probe mean you can expect years of use. pH,

• EC (electrical conductivity), TDS (ppm) with automatic temperature compensation
• replaceable, integrated pH, EC and TDS (ppm) SE600 probe with a 1 m cable (included in
• the set) large, easy-to-read display
• factory calibrated (single-point calibration for pH and EC)
• measurement range: 0.00 - 14.00 pH / 0.00 - 6.00 mS/cm / 0 - 4000 ppm measurement accuracy: ±0.2 pH / ±2%
• full scale EC/TDS specially designed for use in
• hydroponics, aquariums and greenhouses Instructions for use and technical

specifications here. temperature compensation: automatic, 0 - 

• 50°C calibration: initially factory, manual, single-point
• pH calibration: solution for pH
• 7.01 calibration - 20 ml EC / TDS calibration: 1413 µS/cm
• calibration solution - 20 ml or 1500 ppm calibration solution - 20 ml probe: integrated combination SE-600 operating environment: 0 - 50°C;
• max. 95% RH. battery
• type: 1 x 9V battery life: approximately 150
• hours of use automatic shut-off (auto-off)
• function: after 8 min. of inactivity dimensions:
• 143 x 80 x 32 mm weight: 220 g 
• (with batteries) device warranty: 2 years
• probe warranty: 6 months pH
• and conductivity are extremely important
• for professional gardeners and large-scale

growers. pH can affect plants' uptake of nutrients and water and reduce the effectiveness of fertilisers, herbicides and pesticides. Managing conductivity helps growers determine the precise fertiliser or other plant needs. Care and use: The MW802 PRO portable 3-in-1 meter includes both a pH and

EC sensor in the integrated SE600 probe. All pH sensors have a limited lifespan, and their response time becomes longer over time. EC sensors are more robust but can still be affected by residue build-up. Both require maintenance. Proper maintenance of your probe will give you fast, accurate results for longer. Here are our four top tips. Always store with the cap filled with buffer

1. or MA9015 storage solution, and not with water. Clean your probe regularly by soaking it in
2. MA9016 cleaning solution. Calibrate after cleaning and/or storage before testing
3. to correct changes in the pH and EC sensor. Gently stir the probe
4. in the sample for a faster result.

Quickly and consistently measure moisture, nutrient levels (measured via electrical conductivity) and temperature directly in the root zone. Bluelab Pulse Meter connects directly to your smartphone via the Pulse app for automated data collection, measurement comparison, storage and export.

Download the Pulse app for Android (version 5.1 and later) here!

• Measures electrical conductivity, moisture and temperature
• Probe length 20cm
• Total instrument length 50cm
• Minimum pot size 2L.
• Android version 5.1 and later
• Bluetooth version 4.0 and later
• iOS 12.1 + (iPhone only)
• 1 x AA alkaline battery
• 1-year warranty

Bluelab Pulse Meter allows you to take measurements regardless of the growing medium: soil, coco or rockwool. Measuring, comparing and adjusting data is now faster than ever. Achieve better yields, reduce shrinkage and grow healthier plants!

Plant health is in your hands.

Stay informed about moisture levels: optimise irrigation cycles and water use; control the risk of root infections.

Stay informed about nutrient levels: optimise growth by providing the right amount of nutrients for your plants’ growth stage.

Stay informed about temperature levels: optimise root function; monitor for temperature fluctuations.

• Broaden your horizons with the latest technology and deepen your knowledge of plants and their performance!
• Take more, faster measurements with direct measurement technology!
• View all root-zone data, conduct research and take notes in the Pulse app!
• Set target ranges for nutrient and moisture levels and receive immediate real-time feedback in the field!

Product technical specifications here!

Milwaukee MA911B/2 is a replacement pH probe for the pH meter Milwaukee MC110 PRO (sold separately).

• measures: pH and temperature of solutions
• measurement range: 0.0 - 14.0 pH
• operating environment: -5 to 70°C
• dimensions: 12 / 16 cm, ⌀ 1.27 cm
• cable length: 2 m
• connection: BNC
• warranty: 6 months

You can extend the life of your pH electrode as follows:

1. Storage: The pH probe must be kept hydrated. Long periods of dry storage will harm the probe's sensitivity. Allowing the probe to dry may also cause deposits and clogging at its tip. Storing it in MA9015 storage solution or pH calibration buffers will help address both issues. Do not store in tap water or distilled water! This will damage the probe's sensitivity. The best way to store the probe is with the probe cap filled with storage solution or calibration buffer and the cap tightened to prevent leakage. It is also recommended that the electrode be stored upright to further reduce the potential for leakage.
2. Cleaning: Deposits on the probe tip from the mineral salts of the nutrient solution or from organic material can affect its sensitivity and clog it. We recommend regularly soaking your electrode in MA9016 cleaning solution.
3. Calibration: the glass tip of the pH probe becomes less sensitive over time, so make sure to calibrate regularly to keep your meter accurate. Also calibrate after cleaning or a long period of storage.

professional EC monitor for continuous use

EC monitor for constant monitoring of hydroponic or fertiliser solutions, aquariums and aquaponic systems, swimming pools, etc. Convenient visual-indication function when the solution EC passes a set value (upward or downward, selectable by knob). Manual calibration at EC 1413 μS/cm.


range: 0.0-10.0 mS/cm
resolution: 0.1 mS/cm
accuracy: ±2%
EC indication can be set to: 1-5 mS/cm
calibration: manual, one point
LED indication upon reaching set values
automatic temperature compensation
package includes: 12V power adapter; electrode with 2m cable; calibration solution 1413 μS/cm
Dimensions: 149 x 83 x 32 mm; 160g
Manufacturer's warranty - 2 years for the device, 6 months for the sensor. Does not apply to mechanical damage or improper use!

Bluelab pH ProbePlus is an original replacement probe designed for the professional Bluelab pH PenPlus meter. Thanks to its replaceable design, you can easily restore the instrument's factory accuracy without replacing the entire meter. The probe measures pH and temperature, features Double Junction technology for more stable measurements, and can be replaced in seconds without tools.

Bluelab pH ProbePlus is designed as a replaceable measuring module for the Bluelab pH PenPlus and is made to provide long-term reliability and maximum accuracy when measuring pH. Rather than replacing the entire instrument after the electrode's natural wear, you only need to replace the probe. This reduces costs, minimises downtime and extends the life of your pH PenPlus.

The probe uses a Double Junction (double-junction) pH electrode, which provides more stable readings and a longer service life than standard pH electrodes. This technology reduces the risk of contamination of the reference system and ensures reliable measurements even during intensive daily use in nutrient solutions.

The built-in temperature sensor enables simultaneous measurement of pH and temperature, ensuring correct results under different operating conditions. Thanks to the screw mounting system, the probe can be replaced quickly and without tools.

The probe is supplied with a KCl silicone cap with an internal sponge, which keeps the electrode continuously hydrated during storage. With proper maintenance, regular cleaning and periodic calibration, ProbePlus delivers long-lasting, reliable performance.

Technical specifications

✔️ Manufacturer: Bluelab

✔️ Model: pH ProbePlus (PROBPLUSPH)

✔️ Type: Replacement pH and temperature probe

✔️ Compatibility: Only with Bluelab pH PenPlus

✔️ Measured parameters:

• pH
• Temperature

✔️ pH range: 0.0 – 14.0 pH

✔️ Operating temperature: 0 – 50°C

✔️ Temperature: 0-50°C

✔️ Double Junction pH technology

✔️ Screw system for quick replacement

✔️ Tool-free replacement

✔️ KCl silicone cap with internal moistening sponge

✔️ Designed for professional daily use

✔️ Limited warranty: 6 months

📦 The set includes

✔️ 1 × Bluelab pH ProbePlus

✔️ 1 × Buffer solution pH 7.0 (18 ml)

✔️ 1 × Buffer solution pH 4.0 (18 ml)

✔️ 1 × KCl Storage Solution (18 ml)

✔️ 1 × Quick-start guide

Benefits

✔️ Original replacement probe from Bluelab

✔️ Replace only the probe, not the entire device

✔️ Restores the factory accuracy of pH PenPlus

✔️ Double Junction technology for longer life

✔️ Quick tool-free replacement

✔️ Measures pH and temperature simultaneously

✔️ Reduces maintenance costs

✔️ KCl cap protects the electrode from drying out

✔️ Suitable for professional daily use

🔧 Application

Suitable for:

• Hydroponic systems

• Coco substrates

• Soil cultivation

• Aquaponics

• Greenhouses

• Measuring nutrient solutions

• Laboratory applications

• Professional horticulture

• Only for Bluelab pH PenPlus

📋 How to use

1. Unscrew the used probe from Bluelab pH PenPlus.
2. Screw in the new Bluelab pH ProbePlus until snug.
3. Calibrate the probe with the pH 7.0 and pH 4.0 buffer solutions.
4. Rinse the probe with clean water after every measurement.
5. Always store the electrode in KCl solution inside the protective silicone cap.
6. Clean and calibrate regularly for maximum accuracy.

⚠️ Important: pH electrodes are consumable items. Their sensitivity naturally decreases over time. Replace the probe if readings stabilise more slowly or calibration becomes difficult. With proper maintenance and storage, Bluelab pH ProbePlus provides reliable long-term performance.

💡 Urban Botaniks tip: To maximise probe life, use Bluelab pH Care Kit regularly for cleaning and calibration, and never allow the electrode to dry out. Storing it in KCl solution ensures a longer service life and consistently accurate measurements.

The waterproof 4-in-1 pH/EC/TDS/Temp tester MW804 MAX by Milwaukee is an "all-in-one" measuring instrument that makes it easy to take daily measurements. It lets you measure the pH, conductivity (EC), total dissolved solids (TDS) and temperature of the nutrient solution.

• measuring range: 0.00-14.00 pH / 0.00 - 20.00 mS/cm EC / 0.00 - 10.00 ppt TDS / 0.0 - 50.0°C temp.
• resolution: 0.01 pH / 0.01 mS/cm / 0.01 ppt / 0.1°C
• accuracy: ±0.05 pH / 2% EC/TDS / ±0.5°C
• calibration: automatic
• fast and easy-to-read results on a large digital LCD display
• automatic shut-off function (auto-off): after 8 minutes of inactivity
• completely waterproof (IP65)

Instructions for use here*.

Features:

• measuring range: 0.00-14.00 pH / 0.00 - 20.00 mS/cm EC / 0.00 - 10.00 ppt TDS / 0.0 - 50.0°C temp.
• resolution: 0.01 pH / 0.01 mS/cm / 0.01 ppt / 0.1°C
• accuracy: ±0.05 pH / 2% EC/TDS / ±0.5°C
• automatic temperature compensation
• calibration: automatic, 1-point for EC and 1- or 2-point for pH
• sensor: Mi60P (replaceable)
• operating environment: 0 - 50°C; max. relative humidity 100%
• battery type: 4x 1.5V; IEC LR44, A76 (included)
• battery life: approx. 100 h of use
• automatic shut-off function (auto-off): after 8 minutes of inactivity
• length/diameter dimensions: 20 cm / ⌀ 3.8 cm
• weight: 99 g
• instrument warranty: 2 years
• sensor warranty: 6 months

The MW804 MAX tester includes both a pH and an EC electrode. Both of them require maintenance.
All pH sensors have a limited lifespan and their response time becomes longer over time. EC sensors are more robust, but they too can be affected by the buildup of nutrient residues. So, do not forget to order Milwaukee electrode storage and cleaning solutions MA9015 and MA9016! They will help extend the service life of your instrument!

Here are our top five tips.

1. Always store it with the cap filled with buffer or MA9015 storage solution, and not water.
2. Clean your probe regularly by soaking it in MA9016 cleaning solution.
3. Calibrate after cleaning and/or storage before testing to correct changes in the pH and EC sensor.
4. Stir the nutrient solution gently for a faster result.
5. To minimise buildup, always rinse the probe with fresh tap water after every use!

Milwaukee EC40 EC/TDS Nutrient Meter measures electrical conductivity (EC) and total dissolved solids (TDS) in nutrient solutions used in hydroponics, horticulture or agriculture. With this device, you will always know the exact nutrient levels your plants receive, ensuring healthy growth and zero product waste. Measures electrical conductivity (EC) and

• total dissolved solids (TDS) with automatic temperature compensation Ideal for hydroponic use: provides readings on
• the EC, CF, ppm700 and ppm500 scales Measuring range: 0.2–4 mS/cm / 2–40 CF /
• 140–2800 ppm (0.7 scale) / 100–2000 ppm (0.5 scale) Measurement accuracy (EC): ±4% at 25°C Units displayed
• directly in mS/cm/CF/PPM (no conversions
• required) Factory calibrated; continuous calibration is not required
• Automatic on/off functions: auto-off / auto-on Blue
• LED indicators Battery level indicators Instructions for
• use: here*!
• When growing hydroponically, it

is essential to

know the exact concentration of the nutrient solution before giving it to your plants. If the measured conductivity readings are low, your plants may not receive enough nutrients and may develop mineral deficiencies. Conversely, if readings are too high, plants can suffer nutrient burn. To take a measurement, simply place the probe in the solution and the reading will appear on the blue LED display.

Key features:

• Measures electrical conductivity (EC) and total dissolved solids (TDS) with automatic temperature compensation Measuring range:
• 0.2–4 mS/cm / 2–40 CF / 140–2800 ppm (0.7 scale) / 100–2000 ppm (0.5 scale) Units displayed directly in
• mS/cm/CF/PPM (no conversions required) Factory calibrated; continuous calibration
• is not required Blue LED indicators
• Battery level
• indicators Automatic on/off functions:
• auto-off / auto-on Battery life: up to 3
• years (with approx. 10 measurements per day) Batteries: 3x
• 1.5V AA (included) Length/diameter:
• 42 cm / ⌀ 3 cm Weight:
• 255 g
• warranty: 2 years

Maintenance:

• EC / TDS electrodes can develop nutrient buildup over time. To minimise buildup, always rinse the probe in fresh tap water after each use!

With the Milwaukee MA871 Digital Refractometer (0 - 85% Brix), measuring sugar content is now child's play!

The Milwaukee MA871 Digital Refractometer features automatic temperature compensation and a range of 0 - 85% BRIX and +/- 0.2% accuracy. It is easy to use, with simple two-button operation and a response time of under 2 seconds. Maintenance is straightforward thanks to the easy-to-clean, sealed crystal-glass prism and stainless-steel sample well.

• Ideal for winemakers, brewers, fruit and vegetable growers, maple syrup producers and food manufacturers.
• Fast and accurate results with a digital dual-level LCD display.
• Easy measurement with just 2-3 drops of sample and results in under 2 seconds.
• Easy one-point calibration using distilled or deionised water.
• Easy-to-clean stainless-steel sample well with a unit rated IP65 as "dustproof" and protected against water jets.

Instructions for use here.

Specifications:

• measurement range: 0 - 85% BRIX, 0 - 80°C
• resolution: 0.1% BRIX, 0.1°C
• accuracy: ±0.2% BRIX, ±0.3°C
• light source: yellow LED
• measurement time: approximately 1.5 seconds
• min. sample volume: 100 µL or 2 drops (fully cover the prism)
• sample cell: stainless-steel ring and flint glass prism
• temp. compensation: automatic, between 10 and 40°C
• housing protection rating: IP65
• housing material: ABS
• battery type: 1 x 9V AA (included)
• battery life: 5000 hrs of readings with automatic shut-off after 3 minutes of inactivity
• instrument dimensions:192 x 102 x 67mm
• instrument weight: 0.42 kg
• package dimensions: 268 x 122 x 118mm
• warranty: 2 years

Bluelab pH Probe is a replacement pH probe suitable for use with Bluelab pH Meter, Bluelab Combo Meter and Bluelab Guardian Monitor.

• completely waterproof
• 2-metre cable for measurements in hard-to-reach places
• fast and accurate measurements
• polycarbonate housing for long-lasting use
• effective in solutions with EC of 0.2 and higher
• warranty: 6 months

Use in conjunction with the included storage cap with KCl to extend probe life!

Product technical specifications here!

The Bluelab pH Probe is a replaceable pH probe (electrode) suitable for use with the Bluelab Combo Meter, pH Meter and Guardian Monitor. Unfortunately, pH probes don't last forever as they age through daily use and eventually break. With good care and proper use (keeping the tip of the probe wet and cleaning it once a month) you will extend its lifespan. Bluelab pH Probe can be used by everyone from home hobbyists to professional greenhouse gardeners. Replace only the pH probe, not the entire unit!

Bluelab Grower`s Toolbox is a set of instruments for measuring the pH and electrical conductivity of the nutrient solution:

• Bluelab pH pen
• Bluelab EC pen
• 1-year warranty

Product technical specifications here!