Lighting special offers

Stucco – reflector with E40 socket

The textured Stucco Reflector is a low-cost open-type reflector (natural dissipation of heat from the bulb).

• made of textured polished aluminum
• dimensions L/W/H: 47 x 38 x 11.5cm.
• ceramic socket: E40 (included)
• suitable for: 250W, 400W, 600W MH / HPS bulbs

PowerPlant Superveg 600W – MH lamp

Metal halide / MHbulb / lamp for the growth / vegetative stage.

Metal halide lamp, suitable for plants in the vegetative stage. Connect to a 600W ballast.

Improved output in the blue spectrum for vigorous growth.

• Socket: E40
• Coverage area: 1.44 m²
• Light output: 51,000 Lm
• Efficiency: 85 Lm/W
• Lifetime: 10,000 hours
• Color temperature: 4000 K

Note:to ignite the lamp, it must be connected to a choke and ignitor or an electronic ballast, which are sold separately (you can buy them here*).

Warning:

• The cable connecting the ballast to the reflector should be no more than 2 m long!

LUMii Digita 600W – electronic ballast

LUMii Digita 600W Electronic Ballast is an electronic/digital ballast/choke with dimming capability (reducing or increasing the power) for 600W high-pressure sodium (HPS) or metal halide (MH) lamps/bulbs. LUMii Digita 600W Electronic Ballast is an electronic choke with a built-in microprocessor that controls the unit and operates at a higher frequency than standard analog chokes. Greater efficiency means more light for your plants. It allows the bulb to ignite quickly, thereby saving energy. Quieter than any other choke. Measurements indicate up to 30% greater brightness than analog chokes. An electronic choke solves the problem of irregular mains voltage! Analog chokes age over time, become noisy and consume more electricity, heat up more and more, while their light output decreases. This does not happen with electronic chokes; they maintain the same level of light output and efficiency. To ensure safe operation, the LUMii ballast is programmed to switch off in the event of a short circuit, if the bulb burns out, or if no bulb is present.

​

• operating modes with a 600W lamp/bulb: 250W, 400W, 600W
• operating modes with a 400W lamp/bulb: 250W, 400W, do not dim above 400W!
• operating modes with a 250W lamp/bulb: 250W, do not dim above 250W
• Supply voltage: 220–240V 50Hz
• Amperage: 1.8A
• Input power: 620W
• Output power: 600W
• Efficiency: >0.99 THD
• Harmonic distortion: <10%, Imax:Iavg. <1.7
• Ambient temperature: from -25°C to 70°C
• Temperature rise (Δt): 29°C
• Protection rating: >IP23
• ​Dimensions L/W/H: 43/38/18.5cm
• Weight: 3.125kg

Disconnect the power supply when changing the lamp!

LUMii BLACK Reflector

The LUMii BLACK Reflector includes:

•  5 m cable 
•  E40 socket

Dimensions:

• Height: 130 mm 
• Width: 380 mm
• Length: 510 mm

Easy Rollers – accessory

With Easy Rollers you can quickly and easily adjust the height of your lights.

• support up to 10kg.

Sylvania GroLux 250W – HPS lamp

Sylvania GroLux SHP-TS 250W is a dual-spectrum sodium / HPS bulb / lamp, suitable for both growth / vegetative growth and the flowering stage.

• for growth and flowering
• Power: 250W
• Amperage: 2.6A
• Luminous flux: 34,000 lm, 75,500 Phyto-lm
• Efficiency: 136 lm/W
• Color temperature: 2050 K
• Lifespan: 26,000 h
• Socket: E40

Note:to ignite the lamp, it is necessary to connect it to a ballast and ignitor or an electronic ballast, which are sold separately (you can purchase them here*).

Detailed specifications:here*

Recommendations:

• Connects to the mains through a suitable ballast.
• Position at least 40 cm from the plant tops!
• Recommended ambient temperature: 25°C
• To get the maximum performance from sodium lamps, it is recommended that they be used for no more than one year.

Caution:

• Risk of electric shock - disconnect the power before installing, removing, or inspecting the lamp, and protect it from contact with water!
• Do not stare at the light source!
• Fire hazard - keep flammable materials away from the lamp!
• Use only in combination with suitable, thermally protected control gear and a suitable fixture!
• Damaged lamps may emit hazardous radiation and can cause injury, poisoning, property damage, or fire!
• Damaged lamps must be replaced immediately with care and disposed of in accordance with local environmental legislation!
• Risk of burns - allow the lamp to cool first!
• Do not use excessive force when installing a lamp!
• Lamps must be switched off and allowed to cool at least once a week!
• At the end of the lamp’s life - characterized by the lamp switching on and off intermittently or significant changes in color or brightness - the lamp must be replaced immediately!

LUMii CFL Warm White 130W – 2700K

Compact fluorescent lamp (CFL) for flowering, with a built-in electronic ballast (plugs directly into the mains using an E40 socket). It does not generate much heat and can be placed very close to the plants.

• Socket: E40
• Luminous flux: 6300 Lm
• Efficiency: 48 Lm/W
• Lifespan: 10,000 hours
• Color temperature: 2700 K
• Suitable for supplemental lighting, side lighting, mother plants and clones
• Minimal heat emission

• Do not touch the glass part of the lamp with your hands! 
• Do not overtighten in the socket!
• Ensure adequate ventilation!
• Do not use the lamp if it is wet! 
• Do not use in light fixtures with power adjustment (dimmer)!
• Do not use in enclosed light fixtures!

LUMii CFL Warm White 200W – 2700K

Compact fluorescent lamp (CFL) for flowering, with a built-in electronic ballast (connects directly to the mains via an E40 socket). It does not get very hot and can be placed very close to the plants.

• Socket: E40
• Luminous flux: 8050 Lm
• Efficiency: 40 Lm/W
• Lifespan: 10,000 hours
• Color temperature: 2700 K
• Suitable for supplemental lighting, side lighting, mother plants and clones
• Minimal heat output

• Do not touch the glass part of the lamp with your hands! 
• Do not overtighten in the socket!
• Ensure adequate ventilation!
• Do not use the lamp if it is wet! 
• Do not use in dimmable light fixtures!
• Do not use in enclosed light fixtures!

Maxibright Warpdrive 600W – ballast

Maxibright Warpdrive 600W Power Pack is a budget electronic ballast designed for use with 600W high-pressure sodium (HPS) or metal halide (MH) lamps/bulbs. It does not have a "dimming" function (increasing or decreasing the power)!

• operates silently
• extremely lightweight and compact
• works with HPS and MH bulbs

Note: the product is supplied with a UK plug* (UK-standard plug) and IEC-14 female connector*!

Features:

• power: 600W
• dimming capability: none
• ​voltage: 240V
• frequency: 50/60Hz
• Imax: 3.5A
• weight: 1.135kg
• dimensions: 241/100/60mm
• warranty: 1 year

Note: the product is supplied with a UK plug* (UK-standard plug) and IEC-14 female connector*!

HortiLight 600W – magnetic ballast

HortiLight 600W Ballast is an excellent addition to any grow room for those seeking a high-quality and reliable magnetic ballast at a reasonable price. It is designed to work with HPS (sodium) and MH (metal halide) lamps.

• ​forHPS and MH lamps
• power: 600W
• current consumption: 3A
• voltage: 220/240V, 50Hz
• dimensions L/W/H: 310x144x120mm.
• weight: 6.4kg.

Secret Jardin TLED 26W – LED Lamp

Secret Jardin TLED 26W L54cm Blooming is a single LED bar for the growth andflowering stages of indoor plants. Ideal for supplemental vertical lighting for the plants in your tent. 

• for growth andflowering
• power: 26W
• efficacy: 2.0µmol/s
• coverage area: 60 x 40см (when hung 15см from the tops of the plants)
• protection: IP54
• lifetime: + 50 000 hours
• warranty: 1 year
• power cable:yes

Technical specifications:

• for growth andflowering
• power: 26W
• efficacy: 2.0µmol/s
• coverage area: 60 x 40см (when hung 15см from the tops of the plants)
• voltage: 100-220V
• frequency: 50/60 Hz
• dimensions: 54 х 4 х 3см
• weight: 0.36кг
• protection: IP54
• lifetime: + 50 000 hours

LUMii CFL Warm White 300W – 2700K

• Socket: E40
• Light output: 12,950 Lm
• Efficiency: 43 Lm/W
• Lifespan: 10,000 hours
• Color temperature: 2700 K
• Suitable for supplemental lighting, side lighting, mother plants and clones
• Minimal heat emission

Compact fluorescent lamp ( CFL ) for young plants, with a built-in electronic ballast (connects directly to the mains with an E40 socket). Does not generate much heat - can be placed very close to the plants.

• Do not touch the glass part of the lamp with your hands! 
• Do not overtighten in the socket!
• Ensure adequate ventilation!
• Do not use the lamp if it is wet! 
• Do not use in light fixtures with power regulation (dimmers)!
• Do not use in enclosed light fixtures!

Mari 600W – magnetic ballast

Mari 600W is a high-quality and durable product - one of the best-selling products on the market in its class. The lighting set is designed to work with HPS (sodium) and MH (metal halide) lamps.

• the set includes: magnetic ballast, ignitor and capacitor
• for HPS and MH lamps
• power: 600W
• current consumption: 6.2A
• voltage: 230V, 50Hz
• dimensions L/W/H: 295x110x115mm.
• weight: 6.4kg.

Cosmorrow 20W L50 – LED for flowering

Secret Jardin Cosmorrow LED 20W L50cm Blooming is a single LED bar for the flowering phase of indoor-grown plants. Power supply is not included - sold separately! You can purchase it here!

• for flowering
• power: 20W
• voltage: 24V
• efficiency: 1.8µmol/s
• light ratio: 33% 2100°K : 33% 6500°K : 34% 660nm
• coverage area: 60 x 40cm (when suspended 15cm from the tops of the plants)
• water resistance: IP65
• lifespan: 30,000 hours
• warranty: 1 year

Technical specifications:

• for flowering
• power: 20W
• voltage: 24V
• efficiency: 1.8µmol/s
• light ratio: 33% 2100°K : 33% 6500°K : 34% 660nm
• coverage area: 60 x 40cm (when suspended 15cm from the tops of the plants)
• water resistance: IP65
• dimensions: 47 x 3.2 x 1.5cm
• weight: 0.16kg

Garden Highpro PEARLPRO XL – reflector

Garden Highpro PEARLPRO XL is an adjustable* open-type reflector made of high-quality "pearl" aluminum. PEARLPRO XL does not create so-called "hot spots" and distributes light more evenly than other reflectors in this price range. Thanks to its greater light distribution and intensity, the reflector has a larger coverage area. The reflector comes with 3 different spreaders for diffusing the light, allowing you to optimize the lighting for the space in which it is placed.

• made from high-quality "pearl" aluminum
• safe junction box for concealed wiring
• maximum setup dimensions L/W: 55 x 63cm.
• socket: E40 (included)
• suitable for: 250W, 400W, 600W MH / HPS bulbs

Stucco – reflector without a lamp holder

CoolTube-style Stucco reflector.

Secret Jardin TLED 42W – LED Light

Secret Jardin TLED 26W L54cm Full Spectrom is a single LED strip for the growth andflowering stages of plants grown indoors. Ideal foradditional vertical lighting for plants in your grow tent.

• for growth andflowering
• power: 42W
• efficacy: 2.0µmol/s
• coverage area: 120 x 60cm (when hung 15cm from the tops of the plants)
• protection rating: IP54
• lifespan: + 50,000 hours
• warranty: 1 year
• power cable:yes

Technical specifications:

• for growth andflowering
• power: 42W
• efficacy: 2.0µmol/s
• coverage area: 120 x 60cm (when hung 15cm from the tops of the plants)
• voltage: 100-220V
• frequency: 50/60 Hz
• dimensions: 95 х 4 х 3cm
• weight: 0.58kg
• protection rating: IP54
• lifespan: + 50,000 hours

Garden Highpro PEARLPRO – reflector

Garden Highpro PEARLPRO is an open-type reflector that provides up to 10% greater light distribution than a standard Stucco reflector.

• made of high-quality "pearl" aluminum
• safe junction box for concealed wiring
• dimensions L/W/H: 47 x 47 x 11cm.
• socket: E40 (included)
• suitable for: 250W, 400W, 600W MH / HPS bulbs

Osram Vialox NAV-T 600W – HPS lamp

Osram Vialox NAV-T (SON-T) 600W is a sodium / HPS bulb / lamp for the flowering phase.

• for flowering
• power: 600W
• amperage: 6.06A
• luminous flux: 90,000 lm
• efficacy: 150 lm/W
• color temperature: 2000 K
• lifespan: 20,000 h.
• socket: E40

Note:to ignite the lamp, it is necessary to connect it to a ballast and ignitor or an electronic ballast, which are sold separately (you can purchase them from here*).

Detailed specifications:here*

Recommendations:

• Connect to the mains via a suitable ballast.
• Position at least 60 cm from the tops of the plants!
• Recommended ambient temperature: 25°C
• To get the maximum efficiency from sodium lamps, it is recommended not to use them for more than one year.

Warning:

• Risk of electric shock - disconnect the power supply before installing, removing or inspecting the lamp, and protect it from contact with water!
• Do not stare at the light source!
• Fire hazard - keep flammable materials away from the lamp!
• Use only in combination with suitable, thermally protected control equipment and a suitable device!
• Damaged lamps may emit hazardous radiation and may cause injury, poisoning, property damage or fire!
• Damaged lamps must be replaced immediately with care and disposed of in accordance with local environmental regulations!
• Burn hazard - allow the lamp to cool first!
• Do not use excessive force when installing a lamp!
• Lamps must be switched off and allowed to cool at least once a week!
• At the end of the lamp's life - indicated by the lamp switching on and off intermittently or significant changes in color or brightness - the lamp must be replaced immediately!

PowerPlant Superveg 400W – MH lamp

Metal halide / MHbulb / lamp for the growth / vegetative phase.

Metal halide lamp, suitable for plants in the vegetative phase. Connect to a 400W choke.

Improved blue-spectrum output for vigorous growth.

• Socket: E40
• Coverage area: 0.8 m²
• Luminous flux: 38,000 Lm
• Efficiency: 95 Lm/W
• Lifespan: 10,000 hours
• Color temperature: 4000 K

Note:to light the lamp, it is necessary to connect it to a choke and ignitor or an electronic ballast, which are sold separately (you can purchase them here*).

Warning:

• The cable connecting the ballast to the reflector must be no longer than 2 m!

LUMii AeroTube Ø125 mm – reflector

LUMii AeroTube 125 mm is the latest air-cooled reflector. When used with ducting and a fan, this innovative product allows air to flow through the reflector, helping to control the ambient temperature.

• Controls the temperature
• Tempered glass
• Removable lamp holder for easy access and lamp cleaning
• External double-sided reflector for superior light output and distribution
• Includes a 4 m IEC cable
• Recommended power: up to 400W
• ∅125 mm.

Mirror Reflector for CFL Lamps – E40

The Mirror Reflector is a budget-friendly open reflector, suitable for CFL (fluorescent) bulbs / lamps.

• made of polished mirrored aluminum
• dimensions L/W/H: 47 x 42 x 12cm.
• ceramic socket: E40 (included)
• suitable for: 130W CFL bulbs

Azerwing Anodised Medium – reflector

The AZERWING reflector by Prima Klima, with an E40 socket for HPS & MH lamps, provides even light distribution without creating so-called "hot spots". The reflector sheet is made of anodised aluminium with 86% light reflectivity after the forming process.

• Length: 550mm
• Width: ~500-710mm
• Height: ~150-200mm
• Maximum for 1000W
• Weight: 0.90kg

• 86% reflectivity
• Adjustable lighting angle
• Adjustable lamp tilt
• Even light distribution, without hot spots
• Optimal cooling and flexible connection.

Cooltube Ø125×490 mm – tube only

Cooltube is a cooling glass tube designed to provide even lighting for plants without excess heat. It reduces the heat output of the lamp installed inside it by up to 40%. Heat is extracted through suitable ducting connected to the tube.

• Length: 49 cm
• Tube diameter: Ø125 mm
• Suitable for 400w or 600w MH or HPS lamps
• NO reflector
• Includes an E40 socket
• Materials: glass and aluminium

MST Hybrid Ballast 600W – ballast

Electromagnetic hybrid starting and control gear with soft start for 600W high-pressure sodium (HPS) and metal halide (MH) lamps/bulbs. It consists of a choke, starter ("igniter"), capacitor and control circuit.

• power: 600W
• consumption: 660W
• 230V, 50 Hz
• λ>0.9; starting voltage 3.2KV
• protection class IP 20
• dimensions L/W/H: 290x100x80mm
• weight: 6.4kg
• warranty: 1 year